To Next PageTo Next PageWhy does my JVC Receiver remote control not operate as I intend?
The remote control may not be ready for your intended operation. Set the mode selector correctly, then press the corresponding source selecting button or SOUND before operation.
What to do if my JVC RX-F10S remote control does not work?
If your JVC Receiver remote control isn't working, consider these potential causes: * There may be an obstruction hiding the remote sensor on the receiver. Remove any obstructions. * The batteries might be weak. Replace the batteries. * The mode selector could be set to the incorrect position. Ensure the mode selector is in the proper position.
Why is my JVC RX-F10S Receiver remote control not operating correctly?
If the remote control of your JVC Receiver does not operate as intended, it might not be ready for your intended operation. Set the mode selector correctly, then press the corresponding source selecting button or SOUND before operation.
General| Weight | 10.2kg |
|---|---|
| Preset Stations | 30 |
| Power output | 100 watts per channel |
| Total harmonic distortion | 0.8% (1 kHz) |
| Input sensitivity | 200 mV/47 kOhms (line) |
| Signal to noise ratio | 95dB (line) |
| Output | 200mV (line) |
| Video Connections | composite |
| Amplifier Type | Digital |
| RMS Power per Channel (8 Ohms, 20Hz-20kHz) | 100W |
| THD | 0.8% |
| Signal-to-Noise Ratio | 100dB (line) |
| Tuner Type | Digital |
Warnings about opening the unit and exposure to moisture/fire.
FCC statement for USA and ICES-003 for Canada.
Explanation of the /I STANDBY/ON button's operation.
Diagram and list of all remote control buttons and their functions.
Diagrams identifying front panel controls and rear panel input/output terminals.
General installation advice, location recommendations, and handling guidelines.
Instructions for inserting batteries into the remote control.
List of included accessories to verify completeness.
Connecting the AM loop and FM antennas for optimal reception.
Guide for connecting speaker wires and a powered subwoofer.
Connecting a DVD recorder/player via stereo audio and video.
Best connection for DVD Audio using analog discrete output.
Instructions for connecting a VCR using various video cable types.
Connecting a DBS tuner and a TV for viewing.
Connecting digital audio and the AC power cord.
How to turn the receiver on and select an input source.
Choosing between analog and digital input modes.
Controlling volume and selecting digital audio decode settings.
Activating and using headphone listening modes.
Adjusting subwoofer placement and activating TV Direct mode.
Temporarily muting sound, adjusting display brightness, and using the sleep timer.
Information on automatic setting memory and display indicators.
Using sound detection to automatically configure speaker distance and levels.
Procedures for manual setup and a list of available basic settings.
Configuring subwoofer presence and speaker dimensions (SML/LRG/NO).
Configuring speaker distance and subwoofer bass output modes.
Adjusting crossover frequency and LFE level for bass management.
Configuring EX/ES, Dual Mono channels, and Midnight listening mode.
Setting digital inputs, component video mode, and auto surround.
List of adjustable sound parameters and their corresponding page numbers.
Setting individual speaker output levels for balanced sound.
Fine-tuning effect level, panorama, and center tone for surround modes.
Adjusting center channel gain, subwoofer phase, and bass boost.
Managing input signal levels and adjusting frequency equalization.
How to tune radio stations manually and using preset memory.
Adjusting reception mode for clearer FM signals.
Understanding surround sound and Dolby Digital/Pro Logic II technologies.
Explanation of DTS formats and Neo:6 surround processing.
Details on Linear PCM and Dual Mono audio signal formats.
Introduction to DSP modes, DAP, MONO FILM, and ALL CH ST.
Activating 3D Headphone mode for enhanced headphone listening.
Table showing mode availability based on signals and speaker settings.
Using Virtual Surround Back for enhanced rear sound.
Guide to choosing and applying desired surround/DSP modes.
How to disable active surround or DSP modes.
Explanation of AV COMPU LINK and video connection options.
Connecting components and using one-touch playback features.
Automatic TV input selection and power control via AV COMPU LINK.
Using the remote to control JVC VCRs and TVs.
Using the remote for DVD recorder/player playback and settings.
Configuring remote for TV control and listing TV manufacturer codes.
Configuring remote for CATV/DBS control and listing associated codes.
Configuring remote for VCR control and listing VCR manufacturer codes.
Configuring remote for DVD player control and listing DVD player manufacturer codes.
Solutions for common power, sound, and remote control operational problems.
Solutions for issues related to FM reception and noise.
Technical details on video/audio inputs, amplifier output, and audio characteristics.
FM/AM tuner ranges, power consumption, dimensions, and weight.
Detailed power output ratings for front, center, and surround channels.
Details on JVC's warranty policy, service procedures, and what is not covered.
Information on finding authorized service centers and buying accessories.
Caution against attempting internal repairs to avoid electrical shock.
