Kemppi FastMig Pulse 350

Other manuals for Kemppi FastMig Pulse 350

Questions and Answers

C
Cameron MosleyAug 11, 2025
What to do if my Kemppi FastMig Pulse 350 Welding System machine won’t work?
- D
  Deborah BartonAug 12, 2025
  If your Kemppi Welding System machine isn’t working, here are a few things you can check: * Make sure the mains plug is connected. * Ensure the mains power distribution is switched on. * Inspect the mains fuse or circuit breaker. * Verify the power source 0/I switch is in the ON position. * Confirm the interconnection cable set and connectors between the power source and wire feed unit are correctly fastened, referring to the manual schematic if needed. * Check that the earth return lead is connected. * Ensure the function panels are switched on by pressing the orange buttons on the top left.
V
Victor NewmanAug 17, 2025
Why is my Kemppi FastMig Pulse 350 Welding System producing a dirty, poor quality weld?
- E
  Elizabeth BatesAug 17, 2025
  A dirty or poor quality weld from your Kemppi Welding System could be due to several factors: * Check the shielding gas supply. * Verify and set the correct gas flow rate. * Ensure you're using the correct gas type for your specific welding application. * Confirm the correct gun/electrode polarity. For example, when using Fe solid filler wire, the earth return should connect to the – pole, and the wire feed unit to the + pole connector. * Make sure you've selected the correct welding program. * Verify the correct Channel (job) number is selected on the PF65 function panel. * Check for any issues with the power supply, such as a phase down.
G
garciadevinAug 25, 2025
What to do if my Kemppi FastMig Pulse 350 Welding System has variable welding performance?
- J
  james25Aug 25, 2025
  If you're experiencing variable welding performance with your Kemppi Welding System, consider the following checks: 1. Ensure the wire feed mechanism is correctly adjusted. 2. Verify that the correct drive rolls are fitted. 3. Confirm the wire spool overrun tension is properly adjusted. 4. Check the gun liner for blockages and replace it if necessary. 5. Make sure the correct gun liner is installed for the filler wire size and type. 6. Inspect the contact tip for proper size, type, and wear. 7. Ensure the gun isn't overheating during operation. 8. Check all cable connections and the earth return clamp. 9. Review your welding parameter settings.
A
Aaron LiAug 30, 2025
Why is there a high spatter volume with my Kemppi FastMig Pulse 350?
- C
  Christopher SimsAug 30, 2025
  A high spatter volume in your Kemppi Welding System could be caused by: * Incorrect welding parameter values. * Improper inductance/Dynamics values. * Incorrect cable compensation value if using long cables. * Inappropriate gas type and flow. * Incorrect welding polarity or cable connections. * Poor filler material selection. * Incorrect welding program selected. * Incorrect Channel (job) number selection. * Issues with the filler wire delivery system. * Problems with the power supply, such as the absence of 3 x phase.
E
Elizabeth RobinsonSep 5, 2025
How to fix filler wire that won’t feed in my Kemppi FastMig Pulse 350 Welding System?
- K
  Kathryn CruzSep 5, 2025
  If the filler wire won’t feed in your Kemppi Welding System, try these steps: * Check the wire feed mechanism to ensure the pressure arms are closed and properly adjusted. * Verify the welding gun switch function. * Confirm the euro gun collar is correctly fastened to the euro block. * Inspect the gun liner for blockages. * Check the contact tip for size, type, and wear. * Try using an alternative gun.