To Next PageTo Next PageWhat to do if “MCP ERR” appears on Kenwood Two-Way Radio display?
If “MCP ERR” appears on the display of your Kenwood Two-Way Radio (indicating an MCP-2A communications error), consider the following: 1. Ensure that the connection between the TM-D710 and the PC is correct. 2. Shut down other software that you may be running. 3. Turn EchoLink mode OFF. 4. Turn the TM-D710 power source OFF and ON, one time.
Why most keys and the tuning control on my Kenwood Two-Way Radio don't function?
If most keys and the Tuning control on your Kenwood Two-Way Radio do not function, it could be because: 1. One of the Lock functions is ON. Unlock all of the Lock functions. 2. The transceiver is in Channel Display mode. With the transceiver power OFF, press [LOW] + Power ON to exit Channel Display mode.
How to fix Kenwood Transceiver when packet operation results in no connects with other stations?
If packet operation results in no connects with other stations, it could be due to: 1. The squelch is open. Select the correct squelch level so that the squelch is opened only when signals are present. 2. Incorrect data length and parity bit settings. Use HBAUD command to select the appropriate transfer rate.
Why Kenwood Two-Way Radio won't power up?
If your Kenwood Two-Way Radio doesn't power up after connecting a 13.8 V DC power supply, and nothing appears on the display, it could be due to: 1. The power cable being connected backwards. Ensure the red cable is connected to the + terminal and the black cable to the – terminal. 2. One or more of the power cable fuses being open. Look for the cause of the blown fuse(s). After inspecting and correcting any problems, install a new fuse(s) with the same ratings.
Why can't I transmit on my Kenwood Two-Way Radio even when pressing PTT?
If you cannot transmit using your Kenwood Two-Way Radio, even when pressing [PTT], it might be due to the following reasons: 1. The microphone plug may not be fully inserted. Switch the power OFF, then insert the microphone plug until the locking tab clicks in place. 2. You may have selected a transmit offset that places the transmit frequency outside the allowable range. Turn the offset shift function OFF. 3. The external TNC might be transmitting. Press [PTT] after the TNC has finished transmitting.
What to do if memory channels cannot be selected on Kenwood Two-Way Radio?
If memory channels cannot be selected on your Kenwood Two-Way Radio by turning the Tuning control or by pressing microphone [UP]/[DWN], it is because no data has been stored in any Memory channel. Store data in some Memory channels.
Why can't I transmit any APRS data on my Kenwood TM-D710A Transceiver?
There are several reasons why you might not be able to transmit APRS data. It could be because: * Beacon is OFF. To switch it ON, press [KEY], [BCON]. * The squelch is open. Adjust the squelch level so that it only opens when signals are present. * The data band is inactive. If you have blanked the data band, press the appropriate [BAND SEL] (1 s) to activate it. * You have not selected APRS mode. Press [TNC] to enter APRS mode; “APRS” should appear. * You selected Packet mode. Press [TNC], then [TNC] again; “APRS” should appear. * You have not correctly programmed your call sign. Use Menu 600 (BASIC SETTING – CALLSIGN) to correctly program your call sign.
What to do if I did not receive any APRS packet on my Kenwood TM-D710A Transceiver?
If you are not receiving any APRS packets, it could be due to: 1. Incorrect data length and parity bit settings. To fix this, select Packet mode, send the following commands to the TNC, then select APRS mode: AW 8 [ENTER], PAR 0 [ENTER], then RESTART [ENTER]. 2. Incorrect packet transfer rate. Use Menu 601(INTERNAL TNC – DATA SPEED) to select the appropriate packet transfer rate (generally 1200 bps).
Why I cannot activate Visual Scan, Remote Control (K type), nor Repeater (K type) on my Kenwood TM-D710A?
If you cannot activate Visual Scan, Remote Control (K type), nor Repeater (K type), it is likely because you have selected APRS or Packet mode. To resolve this, press [TNC] repeatedly until neither “APRS” nor “PACKET” is visible.
What to do if I did not receive any DX cluster data on my Kenwood TM-D710A?
If you are not receiving any DX cluster data, ensure that you have selected the APRS mode. Press [TNC] to enter APRS mode; “APRS” should appear.
General| Brand | Kenwood |
|---|---|
| Model | TM-D710A |
| Category | Transceiver |
| Language | English |
