3.8.6 Alarm Output
On system setting page, press key 【UP/DOWN】to move the cursor behind【
Remote Control Voice Setting】 then press key【OK】or number 6 to enter setting ,
page, as shown in picture 3-10. With the voice prompt “Please input numbers:”(
No:01-99), then press key【OK】to enter next page; press key【MENU】 to switch
it ON or OFF and press key【OK】to save setting, as shown in picture 3-11. If switch
it on, it means the remote control will sound “didi” when using this numbered
remote control to arm and disarm. The factor y default is on.
3.8.7 Scheduled Arm/Disarm
On system setting page, press key【UP/DOWN】to move cursor behind【Scheduled
Arm/Disarm】 then press key【OK】or number 7 to enter setting page, as shown ,
in picture 3-12. With the voice prompt “Please input numbers:”, enter No between
1-4; then press key【OK】to enter next page;with voice prompt input scheduled
arm time, scheduled disarm time. Move cursor behind scheduled switch, press
key【MENU】to switch it ON or OFF and press key【OK】to save setting, as shown
in picture 3-11. If switch it on, the host will automatically arm and disarm in
preset time.
Arming time： ：
Disarm time： ：
Week：
Timing：ON
User code：0000
Arm&Disarm：No send
Test time： ：
Test week：
OK.Ent e r ES C . Retur n OK.Ent e r ES C . Retur n OK.Ent e r ES C. Return
Picture 3-12 Picture 3-13 Picture 3-14
Timing Settings
Enter Number(1-4)：
Timing Settings CID Settings
3.8.8 Scheduled Arm/Disarm
On system setting page, press key【UP/DOWN】to move cursor behind【Network
Center Setting】 then press key【OK】or number 8 to enter setting page, as shown ,
in picture 3-14.
3.8.8.1 User Area Code
On network center setting page, input four CID code in【User Area Code】 press
key【OK】to save setting. The factor y default is 0000.
,
3.8.8.2 Arm/Disarm Upload
On network center setting page, press key【DOWN】to move cursor behind【Arm
/Disarm Upload】 press key【MENU】to switch 【Not Upload】/【Arm Upload】,
/【Disarm Upload】/【Arm/Disarm Upload】 press key【OK】to save setting. The ,
factor y default is【Not Upload】.
3.8.8.3 Self Test Time
On network center setting page, press key【DOWN】to move cursor behind【Self
Test Time】 input self test time, press key【OK】to save setting.,
3.8.8.4 Self Test Week
On network center setting page, press key【DOWN】to move cursor behind【Self
Test Week】 input any week no. 1234567, press key【OK】to save setting.,
3.8.9 Low Batter y and Anti-tamper Setting
On system setting page, press key【UP/DOWN】to move cursor behind【Low
Batter y and Anti-tamper Setting】, press key【OK】or number 9 to enter setting
page, as shown in picture 3-15..
3.8.9.1 Back Light Power Saving
On low batter y and anti-tamper setting page, on the item【Back Light Power
Saving】 press key【MENU】to switch on or off and press key【OK】to save ,
setting. If switch it on, TFT color display will close to save power. The factory
default is open.
3.8.9.2 Anti-tamper Switch
On low batter y and anti-tamper setting page, press key【DOWN】to move cursor
behind【Anti-tamper Switch】, press key【MENU】to switch on or off and press
key【OK】to save setting. If switch it off, the host will not alarm if anti-tamper
switch is triggered. The factor y default is open.
3.8.9.3 Illegal Arm
On low batter y and anti-tamper setting page, press key【DOWN】to move cursor
behind【Illegal Arm】, press key【MENU】to switch on or off and press key【OK】
to save setting. If switch it on, the host cannot arm if it fails to receive the signal
sent by sensor closure. The factory default is close.
1.Part recover y
2.Full rec over y
Please hold <OK> key 10
seconds!
Picture 3-15 Picture 3-16 Picture 3-17
LCD Saved&Tamper
LCD Save: ON
Tamper : ON
Illegal Arming:OFF
AC Failure:0
OK.Ent e r ES C . Retur n OK.Ent e r ES C . Retur n OK.Ent e r ES C. Return
Restore Factor y Full recover y
3.8.9.4 Power Off Setting
On low battery and anti-tamper setting page, press key【DOWN】to move cursor
behind【Power Off Setting】, input 0-5, press key【OK】to save setting. 0 means
close prompt function, 1 means AC off, 2 means dialing, 3 means dialing+siren,
4 means dialing+linkage, 5 means dialing+siren+linkage, The factory default
is 0.
To Next Page
Loading...
