Korg Electronic Keyboard - 52: Stereo Random Phaser

Effect Guide
806
MIDI/Tempo Sync [Check-box]
BPM [MIDI, 40.00…240.00]
Base Note […]
Times [x1…x32]
When MIDI/Tempo Sync is on, the LFO speed is set by
BPM, Base Note, and Times, instead of Frequency. For
more information, see “MIDI/Tempo Sync” on
page 777.
Type [Individual, Common1, Common2]
This controls whether the effect uses its individual
LFO, or one of the Common FX LFOs. For more
information, see “LFO Type” on page 777.
Common LFO Phase Offset [degrees] [+/–180]
When Type is set to Common FX LFO 1 or 2, this lets
you offset the phase from the master LFO.
OUTPUT
Wet/Dry [–Wet… –1:99, Dry, 1: 99…Wet]
Sets the balance between the “wet” processed sound
and the dry input. Negative values invert the phase of
the wet signal. This interacts with Resonance; for more
information, see “Resonance” on page 805.
Source [Off…Tempo]
Selects a modulation source for Wet/Dry.
Amount [+/–100]
Sets the modulation amount for Wet/Dry.
052: Stereo Random Phaser
This is a stereo phaser. The effect uses a step-shape
waveform and random LFO for modulation, creating a
unique phasing effect.
PHASER
Manual [0…100]
Sets the frequency to which the effect is applied.
Depth [0…100]
Sets the depth of LFO modulation.
Resonance [+/–100]
This controls the intensity of the phaser. For more
information, see “Resonance” on page 805.
High Damp [%] [0…100]
Sets the resonance damping amount in the high range.
p.805.
LFO
Waveform [Step-Tri, Step-Sin, Random]
Selects the LFO Waveform. For more information, see
“Waveform” on page 779.
Phase [degrees] [–180…+180]
Sets the LFO phase difference between the left and
right. See “Phase [degrees]” on page 779.
Frequency [Hz] [0.02…20.00]
Step Frequency [Hz] [0.05…50.00]
Source [Off…Tempo]
Amount [–20.00…+20.00]
Step Amount [–50.00…+50.00]
These parameters control the speed of the LFO when
MIDI/Tempo Sync is Off. For more information, see
“Frequency” on page 779.
MIDI/Tempo Sync [Check-box]
BPM [MIDI, 40.00…240.00]
Base Note […]
Times [x1…x32]
Step Note […]
Times [x1…x32]
These parameters control the speed of the LFO when
MIDI/Tempo Sync is On. For more information, see
“Frequency” on page 779.
Type (Step) [Individual, Common1, Common2]
Common LFO Phase Offset [degrees] [+/–180]
These parameters control the LFO source for the steps;
they do not affect the triangle or sine LFOs. For more
information, see “Step LFO type” on page 779.
OUTPUT
Wet/Dry [–Wet… –1:99, Dry, 1: 99…Wet]
Sets the balance between the “wet” processed sound
and the dry input. Negative values invert the phase of
the wet signal. This interacts with Resonance; for more
information, see “Resonance” on page 805.
Source [Off…Tempo]
Selects a modulation source for Wet/Dry.
LFO: Step-Tri/Random
Left
Right
Resonance
LFO Phase
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
Phaser
Phaser