142
Disk edit environment
Page 9 - Utilities 2
1. Prepare 5 disks. Disks don’t need to be formatted,
because Pa50 will format them for you during the
Backup procedure.
2. Select the Backup Data command.
3. The “Are you sure?” message appears. Press ENTER to
continue, EXIT to abort.
4. The “Insert backup disk #1 and press Enter” message
appears. Insert a disk and press ENTER
5. When the Pa50 asks for it, insert a new disk into the
floppy disk drive. Write the disk number on each disk’s
label.
If a disk is not formatted or empty, Pa50 asks if you want
to format it:
Keep SHIFT pressed, and press ENTER to format the
disk. Pa50 first tries a Fast Format, then makes a Full
Format if the former is not possible.
Restore Data
This command restores the backup of the internal factory
data, executed with the “Backup Data” command.
Note: Should your Factory Data disks become corrupt, you can
download the data from www.korgpa.com, or ask your local
KORG dealer.
Warning: Don’t play on the keyboard while restoring data, and
stay in the Disk mode. Wait until the “Wait” message disap-
pears, and the WRITE/DISK IN USE LED turns off.
1. Select this command.
2. The “Are you sure?” message appears. Press ENTER to
continue, EXIT to abort.
3. The “Insert backup disk #1 and press Enter” message
appears. Insert the first backup disk, and press ENTER.
4. Wait until the first backup disk has been read. A message
will appear: “Insert backup disk #2 and press Enter”.
Insert the second backup disk and press ENTER.
5. Repeat the same procedure with backup disks #3, #4 and
#5. When the backup disk #5 has been loaded, the
backup data has been restored into the internal memory.
Note: After the last disk has been loaded, a “Some files
missing” message may appear. This may refer to some User
data, so it is not a problem. Press EXIT to exit the message.
6. When the Wait message has disappeared, and the
WRITE/DISK IN USE LED has turned off, turn the
instrument off, then on again.
Note: At the end of a Restore Data operation, the “Missing some
files” error message may appear. This is due to the lack of Per-
formance banks 11-20 on older versions of the operating system
of Pa80, whose disk you are probably reading. However, this is
not a problem. Press EXIT to close the message window.
PAGE 9 - UTILITIES 2
This page includes the Protect functions.
Global Protect
When loading a “.SET” file, this parameter (if On) protects
the Global from being reprogrammed by the loaded data. All
Global parameters are therefore left unchanged.
When loading a single “.GLB” file, this parameter is ignored,
and the Global is overwritten by the loaded data.
Note: This parameter is saved in memory, but not on disk.
Factory Style Protect
When On, this parameter protects the Factory Styles (from
the “8 BEAT/16 BEAT 1” to the “TRADITIONAL” bank)
from being overwritten when loading data from disk. Fur-
thermore, you can’t access these banks when saving data.
When Off, you can load or save User Styles even into the Fac-
tory Styles banks (from “8 BEAT/16 BEAT 1” to “TRADI-
TIONAL”). This way, you can personalize your Factory Style
banks.
Please note that the Save All procedure always saves only the
USER Style banks.
Note: This parameter is automatically set to On when turning
the instrument off.
Note: Should your accidentally delete some Factory Data,
reload the Backup data, contact your KORG dealer or service
center, or download the data from www.korgpa.com.
Insert 1.4MB FD #1
and press Enter
Disk not empty!
Sh+Enter to format
Global Protect:Off
Fact.Style Protect:On
Disk:Utilities2
To Next Page
Loading...
Need help?
General
