Kramer KDS-7-MNGR

Kramer Electronics Ltd.
KDS-7-MNGR – Protocol 3000
70
Function
Description
Syntax
Response
Parameters/
Attributes
Example
NET-MAC?
Get the MAC
address.
#NET-MAC? <net_id><CR>
~nn@NET-MAC
<net_id>,<mac_address><CR><
LF>
<net_id> - The device
network interface (if there
are more than one).
Counting is 0 based,
meaning the control port
is ‘0’, additional ports are
1,2,3….
<mac_address> - Unique
MAC address. Format:
XX-XX-XX-XX-XX-XX
where X is hex digit
Get the MAC address:
#NET-MAC? 0
PASS
Set password for the
specific user.
+ Require LOGIN
firstly even SECUR
is Off
+ Only admin can
chang other user's
password
#PASS
<user_name>,<password><CR>
~nn@PASS
<user_name>,<password><CR>
<user_name> - The
specific username,
alphanumeric, hyphen
and underscore within 24
characters, hyphen and
underscore can not at
beginning or end
<password> - New
password, 8 to 24
characters (letters,
numbers, and symbols
without spaces or
commas), at least
including one number,
one symbols without
spaces or commas, one
uppercase letter and one
lowercase letter.
Set the admin password to Pass1234:
#PASS admin,Pass1234
PASS?
Get password of the
specific user?
+ Require LOGIN
firstly even SECUR
is Off
+ Only admin can
get other user's
password
#PASS? <user_name><CR>
~nn@PASS
<user_name>,<password><CR>
<LF>
<user_name> - The
specific username,
alphanumeric, hyphen
and underscore within 24
characters, hyphen and
underscore can not at
beginning or end
<password> - Current
password
Get the admin password:
#PASS? admin
RESET
Reset device.
#RESET<CR>
~nn@RESET ok<CR><LF>
N/A
Reset the device:
#RESET
ROLLBACK
Perform firmware
rollback
#ROLLBACK<CR>
~nn@ROLLBACK ok<CR><LF>
N/A
Rollback to previous firmware:
#ROLLBACK
SECUR
Start/stop security.
+ The permission
system works only if
security is enabled
with the “SECUR”
command.
#SECUR <security_state><CR>
~nn@SECUR
<security_state><CR><LF>
<security_state> -
0 - Off (disables
security)
1 - On (enables
security)
Ser device security to on
#SECUR 1
SECUR?
Get current security
state.
The permission
system works only if
security is enabled
with the “SECUR”
command.
#SECUR?<CR>
~nn@SECUR
<security_state><CR><LF>
<security_state> -
0 - Off (disables
security)
1 - On (enables
security)
Get device security:
#SECUR?
SIGNALS-
LIST?
Get signal ID list of
this machine.
+ The response is
returned in one line
and terminated
with<CR><LF>.
+ The response
format lists signal
IDs separated by
commas.
#SIGNALS-LIST?<CR>
~nn@SIGNALS LIST
[<direction_type>.
<port_format>.<port_index>.<sig
nal_type>.<index>,..,]<CR><LF>
<direction_type> -
Direction of the port:
OUT - Output
<port_format> - Type of
signal on the port:
HDMI
<port_index> - The port
number as printed on the
front or rear panel
<signal_type> - Signal ID
attribute:
VIDEO
<index> - Indicates a
specific channel number
when there are multiple
channels of the same type
Get signal list:
#SIGNALS-LIST?
SN?
Get device serial
number.
#SN?<CR>
~nn@SN
<serial_num><CR><LF>
<serial_num> - 14
decimal digits, factory
assigned
Get the device serial number:
#SN?
STANDBY-
VERSION?
Get standby
firmware version
number.
#STANDBY-VERSION?<CR>
~nn@STANDBY-VERSION
<standby_version><CR><LF>
<firmware_version> -
XX.XX.XXXX where the
digit groups are:
major.minor.build version
Get the device standby firmware
version:
#STANDBY-VERSION?
TIME
Set device time and
date.
#TIME <day-of-
week>,<date>,<time><CR>
~nn@TIME <day-of-
week>,<date>,<time><CR><LF>
<day-of-week> - One of
{SUN, MON, TUE, WED,
THU, FRI, SAT}
<date> - DD-MM-YYYY
<time> - Hh:mm:ss
Set device time and date to 5:24:04
on Wednesday may 18
th
2022
#TIME WED,18-05-2022,05:24:04
TIME?
Get device time and
date.
#TIME?<CR>
~nn@TIME <day-of-
week>,<date>,<time><CR><LF>
<day-of-week> - One of
{SUN, MON, TUE, WED,
THU, FRI, SAT}
<date> - DD-MM-YYYY
<time> - Hh:mm:ss
Get device time and date:
#TIME?