Kramer VP-551X - Page 64

Kramer Electronics Ltd.
VP-551X – Protocol 3000
62
Function
Description
Syntax
Parameters/Attributes
Example
STANDBY
Set standby mode.
COMMAND
#STANDBYon_off<CR>
FEEDBACK
~nn@STANDBYvalue<CR><LF>
value – On/Off
0 = Off
1 = On
Set standby mode:
#STANDBY1<CR>
STANDBY?
Get standby mode status.
COMMAND
#STANDBY?<CR>
FEEDBACK
~nn@STANDBYvalue<CR><LF>
value – On/Off
0 = Off
1 = On
Get standby mode status:
#STANDBY?<CR>
TEMPERATURE
?
Get temperature status.
COMMAND
#TEMPERATURE?<CR>
FEEDBACK
~nn@TEMPERATURE?status<CR><LF>
status –
0 = Fail
1 = Pass
Get temperature status:
#TEMPERATURE?<CR>
TEST-MODE
Perform device test
according tow defined
test parameters.
This command starts
device test procedure.
COMMAND
#TEST-MODE<CR>
FEEDBACK
~nn@TEST-MODE result<CR><LF>
result – Test Results
0 = OK
1 = Failed (general)
2…..N – Device specific failed error
code
Perform device test according
to defined test parameters:
#TEST-MODE<CR>
TLK
Set audio talkover mode
status.
COMMAND
#TLKchannel,talkover_mode<CR>
FEEDBACK
~nn@TLKchannel,talkover_mode<CR><LF>
channel = 1 (scaler)
talkover_mode –
0 = off
1 = mixer
2 = talkover
3 = mic only
Set audio talkover mode
status:
#TLK1,1<CR>
TLK?
Get audio talkover mode
status.
COMMAND
#TLK?channel<CR>
FEEDBACK
~nn@TLKchannel,talkover_mode<CR><LF>
channel = 1 (scaler)
talkover_mode –
0 = off
1 = mixer
2 = talkover
3 = mic only
Get audio talkover mode
status:
#TLK?1<CR>
TREBLE
Set audio treble level.
COMMAND
#TREBLEchannel,treble_level<CR>
FEEDBACK
~nn@TREBLEchannel,treble_level<CR><LF>
channel = 1 (scaler)
treble_level – Audio parameter in
Kramer units 0-30
Set audio treble level to 1:
#TREBLE1,1<CR>
TREBLE?
Get audio treble level.
COMMAND
#TREBLE?channel<CR>
FEEDBACK
~nn@TREBLEchannel,treble_level<CR><LF>
channel = 1 (scaler)
treble_level – Audio parameter in
Kramer units 0-30
Get audio treble level:
#TREBLE?1<CR>
VERSION?
Get firmware version
number.
COMMAND
#VERSION?<CR>
FEEDBACK
~nn@VERSIONfirmware_version<CR><LF>
firmware_version – XX.XX.XXXX
where the digit groups are:
major.minor.build version
Get the device firmware
version number:
#VERSION?<CR>
VFRZ
Set freeze on selected
output.
COMMAND
#VFRZout_id,freeze_flag<CR>
FEEDBACK
~nn@VFRZwin_num,freeze_flag<CR><LF>
out_id – 1 (scaler)
freeze_flag – On/Off
0 = Off
1 = On
Set freeze on selected output:
#VFRZ1,1<CR>
VFRZ?
Get output freeze status.
COMMAND
#VFRZ?out_id<CR>
FEEDBACK
~nn@VFRZwin_num,freeze_flag<CR><LF>
out_id – 1 (scaler)
freeze_flag – On/Off
0 = Off
1 = On
Get output freeze status:
#VFRZ?1<CR>
VIDEO-
BYPASS
Set video bypass status.
COMMAND
#VIDEO -BYPASSstatus<CR>
FEEDBACK
#VIDEO -BYBASSstatus<CR>
status – On/Off
0 = Off
1 = On
Set audio-bypass to off:
#VIDEO -BYPASS0<CR>
VIDEO -
BYPASS?
Get video bypass status.
COMMAND
#VIDEO -BYPASS?<CR>
FEEDBACK
#VIDEO -BYPASS?status<CR><LF>
status – On/Off
0 = Off
1 = On
Get audio bypass status:
# VIDEO -BYPASS?<CR>