Kreg ADAPTIVE CUTTING SYSTEM - Troubleshooting Common Issues

TROUBLESHOOTING
1.Burningmaterial
a. Check sharpness of the blade. Replace if necessary.
 b.Checkthebladeforpitchbuild-up.Cleanwithcommercially
available blade cleaner.
 c.CheckToein.(SeeToeinadjustment.)
2.Splinteringontheo󰀨-cut
 a.Verifythesplinterguardcontactstheworkpiece.
 b.Verifythereisnotagapbetweentheinsideedgeofthe
  splinterguardandthebladeteeth.Ifthesplinterguardwas
  nottightenedbeforeuseorloosenedduringuse,itmayhave
  beendamaged.Replacethesplinterguard.
3.Splinteringontheworkpiece(materialunderthetrack)
 a.Verifythefrontedgeofthebladeisushwiththeanti-chip
  strip.Ifthereisagapbetweenthebladeandtheanti-chip
  strip,replaceandtrimthestrip.(SeeTrimtheanti-chipstrip.)
4. Poor dust collection
 a.Emptythedustbagaftereverysecondorthirdcut.
 b.Occasionallyblowoutthedustbagfabricwithcompressedair.
  Accumulatednedustcanclogthedustbagfabricpores.
 c.Verifydustisnotcloggingthebladehousingordustport.Blow
  outthehousingandportwithcompressedair.
 d.Whenmakingmanycutsinoneworksession,connectthe
saw to a shop vacuum.
5.Cutsslightlyo󰀨90°
 a.Verifythebeveloverridesarenotengaged.
b. Check the bevel calibration. (See Calibrate the bevel scale.)
6.Motorboggsdown
 a.Verifythespeed-controldialissettomaximumspeed
  (setting6).
b. Check the sharpness of blade. Replace if necessary.
 c.Checkthebladeforpitchbuild-up.Cleanwithcommercially
available blade cleaner.
 d.Reducefeedrate(movementofsawalongthetrack).Wetor
  hardwoodsrequireaslowerfeedrate.
 e.Bladekerfintheworkpiecemaybeclosingandpinchingthe
  blade.Stopcutting,removethesawfromtheworkpiece,and
  startthecutovertowidenthesawkerf.Ifpinchingpersists,
discard workpiece.
7.Motorstopsworkingafterextendeduse
 a.Inspectpowercordfordamage.
 b.Switchdamagedorworn.CallKregCustomerServicefor
repair.
 c.Motorbrushesworn.CallKregCustomerServiceforrepair.
8. Wavy cut
 a.Verifythetrackingcontrollersareproperlyadjusted.They
  shouldbetightenoughtoeliminateplaybetweenthesawand
  guidetrackwithouthinderingmovementofthesawalongthe
track.
 b.Inspectthetrackingcontrollersfordamage.CallKreg 
Customer Service for repair.
 c.Cleantheanti-slipstripswithadampclothandremovedust
  fromtheworkpiece.Iftheguidetrackslipssidewaysonaslick
workpiece surface, secure the track to the workpiece with
  optionaltrackclamps,availablefromKreg.
9.Sawwillnotplungetodesireddepth
 a.Checkifmodeissettobladechangemode
 b.Makesuresplinterguardhasbeenproperlytrimmed
 c.Makesurethechipstripontheguidetrackhasbeenproperly
trimmed
10.Sawdoesnotsitatonthetrack
 a.Checkifmodeissettobladechangemode
b. Clean track of any debris
 c.Loosenthesnuggersandre-adjust
11.Sawdoesnotglidedownthetrack
 a.Loosenthesnuggersandre-adjust
b. Clean track of any debris
 c.Replaceglidestripsifnecessary
12. Saw blade removal
a. Blade bolt is reverse threaded, turn clockwise to loosen and
remove
13.Sawcatchesatbeginningofcut
 a.Checkthatthesawsnuggersareonthetrack
 b.Loosensnuggersandre-adjust
ATTENTION
!
Should you encounter a problem not addressed above,
call Kreg Customer Service for assistance.
TELL US ABOUT YOUR EXPERIENCE. YOUR OPINION COUNTS.
We’realwaysworkingtoimproveKreg
®
productsandyoursatisfactionwiththemsothatyouhavegreat
project-buildingexperiences.Youcanhelpbysharingyourfeedbackatwww.kregtool.com/feedback.
It only takes a couple of minutes, and will help us to create products and support that serve your needs better.
CUÉNTENOS SOBRE SU EXPERIENCIA. SU OPINIÓN CUENTA.
SiempretrabajamosparamejorarlosproductosKreg
®
ysusatisfacciónconellosparaquetengaexcelentesexperienciasdeconstruccióndeproyectos.
Puede ayudar compartiendo su retroalimentación en www.kregtool.com/feedback. Solo toma un par de minutos y nos estará ayudando a crear
productosybrindarunsoportequesirvamejorasusnecesidades.
PARLEZ-NOUS DE VOTRE EXPÉRIENCE. VOTRE OPINION EST IMPORTANTE POUR NOUS.
NouscherchonstoujoursàaméliorerlesproduitsKreg®etànousassurerquevoussoyezsatisfaitlorsquevouslesutilisezpoure󰀨ectuervosprojetsde
constructionanderendrevotreexpérienceagréable.Vouspouveznousaiderennousfaisantpartdevoscommentairesauwww.kregtool.com/feedback.
Celaneprendquequelquesminutes,etvoscommentairesnousaiderontàcréerdesproduitsetàfournirdesservicesquirépondrontmieuxàvosbesoins.