To Next Page

To Previous Page

Safety

Pos: 11.12 /Übersc hriften/Überschrif ten 2/K-O/L age der Sicher heitsaufkleber a n derM aschine @ 0\mod_11956 34967326_78.d ocx @ 1020 @ 2 @ 1

4.12 Position of the Adhesive Safety Stickers on the Machine

Pos: 11.13 /BA/Sic herheit/Auf kleber/EasyCut/Sic herheitsaufkle ber EasyCut F 2 80/320/360 F 2 80/320/360M @ 103\mod_133 2256664114_78.d ocx @ 9421 33 @ @ 1

Fig. 2 EasyCut F 280, EasyCut F 320, EasyCut F 360

Abb. 3 EasyCut F 280 M; EasyCut F 320 M, EasyCut F 360 M

Table of Contents3
Foreword6
Introduction7
Purpose of Use7
Validity7
Contact7
Identification Plate8
Information Required for Questions and Orders8
Intended Use9
Technical Data9
Safety11
Identifying Symbols in the Operating Instructions11
Identification of the Hazard Warnings11
Personnel Qualification and Training Fehler! Textmarke nicht Definiert12
Dangers in Case of Non-Compliance with the Safety Instructions12
Safety-Conscious Work Practices12
Safety Instructions and Accident Prevention Regulations13
Attached Devices14
PTO Operation15
Hydraulic System16
Tyres16
Maintenance17
Unauthorised Conversion/Modification and Spare Parts Production18
Inadmissible Modes of Operation18
Introduction19
Re-Ordering the Adhesive Safety and Information Labels19
Affixing the Adhesive Safety and Information Labels19
Position of the Adhesive Safety Stickers on the Machine20
Commissioning22
Special Safety Instructions22
First Installation22
Fitting the Guard Cloths23
Installation of Weiste Triangle25
Preparation on the Front-Mounted Disc Mower25
Lighting26
Start-Up27
Mounting Onto the Tractor27
Lower Suspension Arm28
PTO Shaft29
Length Adjustment29
Install the PTO Shaft30
Checking the First Fitting31
Trial Run after First Installation32
Driving and Transport33
Lighting33
Operation35
Before Mowing35
Moving the Guards into the Working Position36
Detaching the Machine37
Removing the Compensation Spring(S)37
Settings39
Compensation Spring(S)40
Adjusting the Compensation Springs41
Adjusting the Cutting Height42
Telescopic Upper Suspension Arm42
Setting of the V-Belt Tension43
Maintenance44
Special Safety Instructions44
Test Run44
Spare Parts45
Tightening Torques45
Tightening Torques (Countersunk Screws)46
Deviating Torque46
Filling Quantities and Lubrication Designations for Gearboxes47
Oil Level Check and Oil Change Intervals (Gearboxes)47
Angular Gearbox47
Angular Gearbox49
Mower Drive Gearbox50
Mower Drive Gearbox51
Oil Level Check and Oil Change on the Cutter Bar52
Oil Change52
Checking the Oil Level52
Aligning the Cutter Bar52
Checking the Cutter Blades and Blade Holder54
Cutter Blades54
Blade Screw Connection55
Blade Quick-Fit Device56
Periodical Inspection of the Leaf Springs57
Periodical Inspection of the Cutting Discs / Blade Drums58
Abrasion Limit59
Blade Changing on Cutting Discs60
Blade Screw Connection61
Blade Quick-Fit Device62
Replacing the Linings63
Rotary Hub with Shear Fuse (Optional)64
After Shearing off66
Maintenance - Lubrication Chart68
Special Safety Instructions68
PTO Shaft68
Lubrication Chart69
Placing in Storage70
Before the Start of the New Season71
Special Safety Instructions71
Test Run71
Special Equipment73
Special Safety Instructions73
Conversion to Narrower Swathing74
Conversion for Mowing Steep Slopes76
Index78

Brand	Krone
Model	EasyCut F 360
Category	Lawn Mower
Language	English

Krone EasyCut F 360 Original Operation Instructions

Table of Contents

Other manuals for Krone EasyCut F 360

Questions and Answers:

Krone EasyCut F 360 Specifications

Related product manuals