KTM 690 Enduro R - User Manual

Questions and Answers

C
Christina WhiteAug 25, 2025
What to do if my KTM 690 Enduro R Motorcycle engine doesn't turn over?
- M
  michelleedwardsAug 26, 2025
  If the KTM Motorcycle engine doesn't turn when you press the starter, it could be due to several reasons. You may not be following the correct start procedure, the battery might be discharged (recharge it and investigate the cause), a fuse (1, 2, 3, or 4) could be blown (replace the fuse), or the main fuse might be burned out (replace it). Other potential causes include a defective ignition/steering lock or emergency OFF switch (have it checked), a problem with the safety start system (have it checked), or a missing ground connection (check the ground connection).
T
Tammy MullinsAug 26, 2025
What to do if my KTM 690 Enduro R engine dies while riding?
- J
  Jessica DavisAug 26, 2025
  If your KTM Motorcycle engine dies while riding, it could be due to several reasons. You might be out of fuel (refuel). A fuse (1, 2, or 4) could be blown (replace the fuse). The engine vent hose might be bent (straighten it or replace if needed). Also, the engine oil level might be too high (check the engine oil level).
K
kimberly68Aug 26, 2025
What to do if my KTM Motorcycle engine doesn't turn over when pressing the starter button?
- K
  Kristin RobinsonAug 26, 2025
  If your KTM Motorcycle engine doesn't turn over when you press the starter, there are several possible causes. It could be due to an operating error, so ensure you are following the correct start procedure. The battery might be discharged, in which case you should recharge it and check the quiescent current. Also, check fuses 1, 2, and 3, as well as the main fuse, and replace them if they are blown. Finally, verify the ground connection is present and properly connected.
R
Robert KramerAug 27, 2025
Why does my KTM Motorcycle engine die while riding?
- A
  Amanda WongAug 27, 2025
  If your KTM Motorcycle engine dies during a ride, there are several possible reasons. You might be running out of fuel, so refuel the motorcycle. Check fuses 1, 2, and 3, as well as the ABS fuse, and replace any that are blown. Another potential cause is a large difference in wheel speeds between the front and rear wheels; if this occurs, stop the vehicle, switch off the ignition, and start it again.
M
mitchell46Aug 27, 2025
Why does my KTM Motorcycle have high oil consumption?
- J
  Jesus YoungAug 27, 2025
  High oil consumption in your KTM Motorcycle could be due to a few reasons. The engine vent hose might be bent, so ensure it is routed without bends or replace it if necessary. The engine oil level might be too high, so check it. Additionally, the engine oil might be too thin (low viscosity), so change the engine oil and filter, and clean the oil screens.
B
Brett TuckerAug 27, 2025
What to do if my KTM Motorcycle engine turns but does not start?
- J
  Jonathan BakerAug 27, 2025
  If the engine of your KTM Motorcycle turns but doesn't start, it could be due to several reasons. You might need to carry out the start procedure. A fuse (fuse 4) might be blown, requiring you to change the fuses of individual power consumers. The coupling of the fuel hose connection might not be connected, so you should reconnect it. There could also be a defect in the fuel injection system, in which case you should read out the fault memory using the KTM diagnostics tool.
D
Diana HowardAug 28, 2025
What to do if my KTM Motorcycle engine dies during the journey?
- D
  Daniel SmithAug 28, 2025
  If your KTM Motorcycle engine dies during a journey, it could be due to a lack of fuel, so refuel. Alternatively, a fuse (1, 2, or 4) might be blown, so change the fuses of individual power consumers.
N
nicholas98Aug 28, 2025
Why is my KTM 690 Enduro R battery discharged?
- E
  Emily PowellAug 29, 2025
  If your KTM Motorcycle battery is discharged, it could be due to a couple of reasons. One possibility is that the ignition was not switched off when the vehicle was parked, so recharge the battery. Another reason could be that the battery is not charged by the alternator, so check the charging voltage and the quiescent current.
T
Terri HallAug 29, 2025
What to do if KTM 690 Enduro R Motorcycle engine does not turn when starter button is pressed?
- K
  Karen HayesAug 29, 2025
  If the KTM Motorcycle engine doesn't turn when you press the starter, it could be due to several reasons. You may need to follow the correct start procedure. The battery might be discharged, requiring a recharge. Check fuses 1, 2, 3, and 4, and replace them if they're blown. Also, inspect the main fuse and replace it if necessary. Finally, ensure that there is a proper ground connection.
A
Anna HallAug 30, 2025
What to do if KTM 690 Enduro R Motorcycle engine turns but does not start?
- C
  Cheryl ColeAug 30, 2025
  If the KTM Motorcycle engine turns but doesn't start, it could be due to a few reasons. You might need to follow the correct start procedure. Fuse 4 might be blown and needs replacing. The coupling of the fuel hose connection may not be connected, so reconnect it. The socket connector of the wiring harness could be oxidized, requiring cleaning and treatment with contact spray. There may be a defect in the fuel injection system, which requires reading the fault memory using the KTM diagnostics tool.

KTM 690 Enduro R Specifications

General

Engine Type	Single cylinder, 4-stroke
Bore x Stroke	105 mm x 80 mm
Torque	73.5 Nm @ 6, 500 rpm
Compression Ratio	12.7:1
Starter	Electric starter
Transmission	6-speed
Cooling	Liquid cooled
Lubrication	Forced oil lubrication with 2 oil pumps
Primary Drive	40:76
Suspension Travel Front	250 mm
Suspension Travel Rear	250 mm
Wheels Front	1.85 x 21"
Wheels Rear	2.50 x 18"
Tires Front	90/90-21
Tires Rear	140/80-18
Chain	X-Ring 5/8 x 1/4"
Seat Height	910 mm
Fuel Tank Capacity	13.5 l
Dry Weight	146 kg
Power	74 hp (55 kW) @ 8, 000 rpm
Fuel System	Keihin EFI (Electronic Fuel Injection)
Clutch	hydraulically actuated
Frame	Chrome-molybdenum steel trellis frame, powder coated
Front Suspension	WP XPLOR USD, Ø 48 mm
Rear Suspension	WP XPLOR
Front Brake	Brembo
Rear Brake	Brembo single piston caliper, 240 mm disc
ABS	Bosch 9.1 MP (disengageable)
Wheelbase	1, 502 mm ± 10 mm

Summary

Safety Advice

Use Definition - Intended Use

Safety Advice

General instructions and warnings for safe vehicle operation.

Degrees of Risk and Symbols

Defines hazard levels (Danger, Warning, Caution, Note) and associated symbols.

Safe Operation

Guidelines for safe riding, including alcohol, drugs, and component temperatures.

Protective Clothing

Recommends wearing appropriate protective gear for riding.

Work Rules

Important Notes

Manufacturer and Implied Warranty

Operating and Auxiliary Substances

Service

Importance of proper service and adherence to intervals for longevity.

Serial Numbers

Chassis Number

Location and identification of the vehicle's chassis number.

Engine Number

Controls

Clutch Lever

Hand Brake Lever

Throttle Grip

Emergency OFF Switch

Electric Starter Button

Ignition;Steering Lock

Combination Instrument

Overview of the instrument cluster functions and displays.

Function Buttons

Indicator Lamps

Meanings and functions of various indicator lamps on the dashboard.

Coolant Temperature Indicator

Shift Lever

Foot Brake Lever

Side Stand

Preparing for Use

Advice on First Use

Essential safety and operational advice for new riders and vehicles.

Running in the Engine

Guidelines for the engine break-in period and maximum RPM.

Loading the Vehicle

Riding Instructions

Performing Checks and Vehicle Care When Preparing for Use

Pre-ride checks for safety and roadworthiness.

Starting

Detailed steps for starting the motorcycle engine safely.

Starting Off

Procedure for safely moving the motorcycle from a standstill.

Shifting, Riding

Guidance on gear shifting, load alterations, and riding techniques.

Applying the Brakes

Instructions and warnings on using the brake system effectively.

Stopping, Parking

Refueling

Safe procedures and precautions for refueling the motorcycle.

Service Schedule

Maintenance intervals and required service tasks for the motorcycle.

Tuning the Chassis

Fork;Shock Absorber

Adjusting the Compression Damping of the Fork

Procedure for adjusting the fork's compression damping.

Adjusting the Rebound Damping of the Fork

Procedure for adjusting the fork's rebound damping.

Compression Damping of the Shock Absorber

Adjusting the Low-Speed Compression Damping of the Shock Absorber

Steps for adjusting the low-speed compression damping of the shock absorber.

Adjusting the High-Speed Compression Damping of the Shock Absorber

Steps for adjusting the high-speed compression damping of the shock absorber.

Adjusting the Rebound Damping of the Shock Absorber

Procedure for adjusting the rebound damping of the shock absorber.

Measuring the Unloaded Rear Wheel Sag

Checking the Static Sag of the Shock Absorber

Checking the Riding Sag of the Shock Absorber

Adjusting the Spring Preload of the Shock Absorber

Steps for adjusting the spring preload on the shock absorber.

Adjusting the Riding Sag

Instructions for adjusting the riding sag, including spring selection.

Adjusting Handlebar Position

Service Work on the Chassis

Raising the Motorcycle with a Lift Stand

Removing the Motorcycle from the Lift Stand

Cleaning the Dust Boots of the Fork Legs

Checking the Play of the Steering Head Bearing

Method for checking steering head bearing play for safe handling.

Adjusting the Play of the Steering Head Bearing

Procedure for adjusting steering head bearing play.

Removing the Air Filter

Installing the Air Filter

Cleaning the Chain

Checking the Chain Tension

Method for checking the drive chain tension.

Adjusting the Chain Tension

Procedure for adjusting the drive chain tension.

Checking the Chain, Rear Sprocket, Engine Sprocket, and Chain Guide

Adjusting Chain Guide

Adjusting Basic Position of Clutch Lever

Checking;Rectifying the Fluid Level of the Hydraulic Clutch

Brake System

Antilock Braking System (ABS)

Explanation of the ABS system, its limitations, and warnings.

Adjusting the Basic Position of the Hand Brake Lever

Checking the Brake Discs

Procedure for checking brake disc thickness and condition.

Checking Brake Fluid Level of Front Brake

How to check the brake fluid level in the front brake reservoir.

Topping Up Brake Fluid of Front Brake

Steps for adding brake fluid to the front brake system.

Checking the Front Brake Linings

Method for inspecting the wear of front brake linings.

Changing the Front Brake Linings

Procedure for replacing worn front brake linings.

Checking the Free Travel of Foot Brake Lever

Adjusting the Basic Position of the Foot Brake Lever

Checking Rear Brake Fluid Level

How to check the brake fluid level in the rear brake reservoir.

Adding Rear Brake Fluid

Steps for adding brake fluid to the rear brake system.

Checking the Rear Brake Linings

Method for inspecting the wear of rear brake linings.

Changing the Rear Brake Linings

Procedure for replacing worn rear brake linings.

Wheels, Tires

Removing the Front Wheel

Installing the Front Wheel

Removing the Rear Wheel

Installing the Rear Wheel

Checking the Tire Condition

Guide to checking tires for cuts, wear, and age.

Checking the Tire Air Pressure

How to check and set correct tire air pressure for different conditions.

Electrical System

Removing the Battery

Steps for safely removing the motorcycle battery.

Installing the Battery

Procedure for correctly installing the motorcycle battery.

Recharging the Battery

Guidelines and precautions for recharging the motorcycle battery.

Changing the Main Fuse

Changing the ABS Fuses

Changing Fuses of Individual Power Consumers

Changing the Headlight Bulb

Checking the Headlight Setting

Adjusting the Headlight Range

Cooling System

Checking the Antifreeze and Coolant Level

Procedure for checking antifreeze and coolant levels.

Checking the Coolant Level

Detailed steps for checking coolant levels in reservoirs and radiator.

Draining the Coolant

Filling;Bleeding the Cooling System

Steps for refilling and bleeding air from the cooling system.

Tuning the Engine

Adjusting the Engine Characteristic

How to adjust engine performance maps for different riding conditions.

Checking the Basic Position of the Shift Lever

Adjusting the Basic Position of the Shift Lever

Service Work on the Engine

Checking the Engine Oil Level

Procedure for checking the engine oil level.

Changing the Engine Oil and Filter, Cleaning the Oil Screens

Comprehensive guide to changing engine oil, filter, and cleaning screens.

Draining the Engine Oil

Instructions for safely draining the engine oil.

Removing the Oil Filter

Steps to remove and replace the engine oil filter.

Cleaning the Oil Screens

Installing the Oil Filter

Filling Up with Engine Oil

How to add the correct amount of engine oil.

Adding Engine Oil

Procedure for adding engine oil and checking for leaks.

Cleaning, Care

Cleaning the Motorcycle

Checks and Maintenance Steps for Winter Operation

Storage

Preparing for Use After Storage

Troubleshooting

Troubleshooting Common Issues

Identifies common faults and their possible causes and actions.

Blink Code

FI Warning Lamp Blink Codes

Lists blink codes for the FI warning lamp and their error conditions.

Technical Data

Engine

Specifications for the motorcycle's engine components and performance.

Engine Tightening Torques

Specified torque values for engine fasteners.

Capacities

Chassis

Electrical System

Tires

Tire specifications, including size, type, and air pressure.

Fork

Shock Absorber

Chassis Tightening Torques

Specified torque values for various chassis fasteners.

Substances

Brake Fluid DOT 4; DOT 5.1

Coolant

Engine Oil (SAE 10 W;60)

Specifications and recommended suppliers for engine oil.

Engine Oil (SAE 10 W;50)

Fork Oil (SAE 4)

Shock Absorber Fluid (SAE 2.5)

Super Unleaded (ROZ 95;RON 95;PON 91)

Related product manuals

KTM 690 Enduro R 2018

276 pages

KTM 690 Enduro R 2021

135 pages

KTM 690 Enduro R 2017

20 pages

KTM 690 Enduro R 2019

274 pages

KTM 690 ENDURO EU 2009

181 pages

KTM 690 ENDURO EU 2008

231 pages

KTM 690 Enduro EU 2010

18 pages

KTM 690 Enduro R EU 2013

234 pages

KTM 690 Enduro R EU 2012

234 pages

KTM 690 Enduro R USA 2012

234 pages

KTM 690 Enduro R - User Manual

Table of Contents

Questions and Answers

KTM 690 Enduro R Specifications

Summary

Safety Advice

Use Definition - Intended Use

Safety Advice

Degrees of Risk and Symbols

Safe Operation

Protective Clothing

Work Rules

Important Notes

Manufacturer and Implied Warranty

Operating and Auxiliary Substances

Service

Serial Numbers

Chassis Number

Engine Number

Controls

Clutch Lever

Hand Brake Lever

Throttle Grip

Emergency OFF Switch

Electric Starter Button

Ignition;Steering Lock

Combination Instrument

Function Buttons

Indicator Lamps

Coolant Temperature Indicator

Shift Lever

Foot Brake Lever

Side Stand

Preparing for Use

Advice on First Use

Running in the Engine

Loading the Vehicle

Riding Instructions

Performing Checks and Vehicle Care When Preparing for Use

Starting

Starting Off

Shifting, Riding

Applying the Brakes

Stopping, Parking

Refueling

Service Schedule

Service Schedule

Tuning the Chassis

Fork;Shock Absorber

Adjusting the Compression Damping of the Fork

Adjusting the Rebound Damping of the Fork

Compression Damping of the Shock Absorber

Adjusting the Low-Speed Compression Damping of the Shock Absorber

Adjusting the High-Speed Compression Damping of the Shock Absorber

Adjusting the Rebound Damping of the Shock Absorber

Measuring the Unloaded Rear Wheel Sag

Checking the Static Sag of the Shock Absorber

Checking the Riding Sag of the Shock Absorber

Adjusting the Spring Preload of the Shock Absorber

Adjusting the Riding Sag

Adjusting Handlebar Position

Service Work on the Chassis

Raising the Motorcycle with a Lift Stand

Removing the Motorcycle from the Lift Stand

Cleaning the Dust Boots of the Fork Legs

Checking the Play of the Steering Head Bearing

Adjusting the Play of the Steering Head Bearing

Removing the Air Filter

Installing the Air Filter

Cleaning the Chain

Checking the Chain Tension

Adjusting the Chain Tension

Checking the Chain, Rear Sprocket, Engine Sprocket, and Chain Guide

Adjusting Chain Guide

Adjusting Basic Position of Clutch Lever

Checking;Rectifying the Fluid Level of the Hydraulic Clutch

Brake System

Antilock Braking System (ABS)

Adjusting the Basic Position of the Hand Brake Lever

Checking the Brake Discs