Why is my KTM 690 Enduro R Motorcycle display blank?
If the combination instrument shows nothing in the display on your KTM Motorcycle, it's possible that fuse 1 is blown. Replace the fuse to see if this resolves the issue.
How to prevent my KTM Motorcycle battery from discharging?
A discharged battery in your KTM Motorcycle can occur if the ignition is not switched off when the vehicle is parked, so always ensure the ignition is off. Another cause can be that the battery is not charged by the alternator, so check the charging voltage and the quiescent current. In both cases you should recharge the battery.
What to do if the headlight and parking light on my KTM 690 Enduro R are not working?
If the headlight and parking light on your KTM Motorcycle are not functioning, the cause might be that fuse 6 is blown. Replace the fuse.
Why aren't the turn signal, brake light, and horn working on my KTM Motorcycle?
If the turn signal, brake light, and horn are not working on your KTM Motorcycle, it is possible that fuse 5 is blown. Replace the fuse.
Why does my KTM 690 Enduro R Motorcycle engine only turn when the clutch lever is pulled?
If your KTM Motorcycle engine only turns when the clutch lever is drawn, the vehicle is likely in gear. Shift gear to neutral. This can also occur if the vehicle is in gear and the side stand is folded out, so shift to neutral.
Why does the combination instrument on my KTM 690 Enduro R display nothing?
If the combination instrument on your KTM Motorcycle shows nothing in the display, it could be due to fuse 1 or 2 being blown. Replace the fuse.
General| Engine Type | Single cylinder, 4-stroke |
|---|---|
| Bore x Stroke | 105 mm x 80 mm |
| Torque | 73.5 Nm @ 6, 500 rpm |
| Compression Ratio | 12.7:1 |
| Starter | Electric starter |
| Transmission | 6-speed |
| Cooling | Liquid cooled |
| Lubrication | Forced oil lubrication with 2 oil pumps |
| Primary Drive | 40:76 |
| Suspension Travel Front | 250 mm |
| Suspension Travel Rear | 250 mm |
| Wheels Front | 1.85 x 21" |
| Wheels Rear | 2.50 x 18" |
| Tires Front | 90/90-21 |
| Tires Rear | 140/80-18 |
| Chain | X-Ring 5/8 x 1/4" |
| Seat Height | 910 mm |
| Fuel Tank Capacity | 13.5 l |
| Dry Weight | 146 kg |
| Power | 74 hp (55 kW) @ 8, 000 rpm |
| Fuel System | Keihin EFI (Electronic Fuel Injection) |
| Clutch | hydraulically actuated |
| Frame | Chrome-molybdenum steel trellis frame, powder coated |
| Front Suspension | WP XPLOR USD, Ø 48 mm |
| Rear Suspension | WP XPLOR |
| Front Brake | Brembo |
| Rear Brake | Brembo single piston caliper, 240 mm disc |
| ABS | Bosch 9.1 MP (disengageable) |
| Wheelbase | 1, 502 mm ± 10 mm |
General instructions and warnings for safe vehicle operation.
Defines hazard levels (Danger, Warning, Caution, Note) and associated symbols.
Guidelines for safe riding, including alcohol, drugs, and component temperatures.
Recommends wearing appropriate protective gear for riding.
Importance of proper service and adherence to intervals for longevity.
Location and identification of the vehicle's chassis number.
Overview of the instrument cluster functions and displays.
Meanings and functions of various indicator lamps on the dashboard.
Essential safety and operational advice for new riders and vehicles.
Guidelines for the engine break-in period and maximum RPM.
Pre-ride checks for safety and roadworthiness.
Detailed steps for starting the motorcycle engine safely.
Procedure for safely moving the motorcycle from a standstill.
Guidance on gear shifting, load alterations, and riding techniques.
Instructions and warnings on using the brake system effectively.
Safe procedures and precautions for refueling the motorcycle.
Maintenance intervals and required service tasks for the motorcycle.
Procedure for adjusting the fork's compression damping.
Procedure for adjusting the fork's rebound damping.
Steps for adjusting the low-speed compression damping of the shock absorber.
Steps for adjusting the high-speed compression damping of the shock absorber.
Procedure for adjusting the rebound damping of the shock absorber.
Steps for adjusting the spring preload on the shock absorber.
Instructions for adjusting the riding sag, including spring selection.
Method for checking steering head bearing play for safe handling.
Procedure for adjusting steering head bearing play.
Method for checking the drive chain tension.
Procedure for adjusting the drive chain tension.
Explanation of the ABS system, its limitations, and warnings.
Procedure for checking brake disc thickness and condition.
How to check the brake fluid level in the front brake reservoir.
Steps for adding brake fluid to the front brake system.
Method for inspecting the wear of front brake linings.
Procedure for replacing worn front brake linings.
How to check the brake fluid level in the rear brake reservoir.
Steps for adding brake fluid to the rear brake system.
Method for inspecting the wear of rear brake linings.
Procedure for replacing worn rear brake linings.
Guide to checking tires for cuts, wear, and age.
How to check and set correct tire air pressure for different conditions.
Steps for safely removing the motorcycle battery.
Procedure for correctly installing the motorcycle battery.
Guidelines and precautions for recharging the motorcycle battery.
Procedure for checking antifreeze and coolant levels.
Detailed steps for checking coolant levels in reservoirs and radiator.
Steps for refilling and bleeding air from the cooling system.
How to adjust engine performance maps for different riding conditions.
Procedure for checking the engine oil level.
Comprehensive guide to changing engine oil, filter, and cleaning screens.
Instructions for safely draining the engine oil.
Steps to remove and replace the engine oil filter.
How to add the correct amount of engine oil.
Procedure for adding engine oil and checking for leaks.
Identifies common faults and their possible causes and actions.
Lists blink codes for the FI warning lamp and their error conditions.
Specifications for the motorcycle's engine components and performance.
Specified torque values for engine fasteners.
Tire specifications, including size, type, and air pressure.
Specified torque values for various chassis fasteners.
Specifications and recommended suppliers for engine oil.
To Next Page