What does it mean if FIbwarning lamp (MIL) flashes briefly 2x on KTM 690 SMC EU?
If the FI warning lamp (MIL) on your KTM Motorcycle flashes briefly 2x, it indicates a malfunction in the ignition pulse generator circuit. In this case, you should check the ignition pulse generator.
What does it mean if FIbwarning lamp (MIL) flashes briefly 6x on KTM 690 SMC EU Motorcycle?
If the FI warning lamp (MIL) on your KTM Motorcycle flashes briefly 6x, it indicates that the input signal from the throttle valve sensor is too low or too high. Check the throttle valve sensor.
What does it mean if FIbwarning lamp (MIL) flashes briefly 8x on KTM Motorcycle?
If the FI warning lamp (MIL) on your KTM Motorcycle flashes briefly 8x, it means that the input signal from the throttle grip sensor is either too low or too high. Check the throttle grip sensor.
What does it mean if FIbwarning lamp (MIL) flashes briefly 9x on KTM 690 SMC EU Motorcycle?
If the FI warning lamp (MIL) on your KTM Motorcycle flashes briefly 9x, it indicates that the input signal from the pressure sensor of the induction manifold is too low or too high. Check the pressure sensor of the induction manifold.
What does it mean if FIbwarning lamp (MIL) flashes 1x long, 2x short on KTM 690 SMC EU?
If the FI warning lamp (MIL) on your KTM Motorcycle flashes 1x long, 2x short, it indicates that the input signal from the coolant temperature sensor is too low or too high. Check the temperature sensor coolant.
What does it mean if FIbwarning lamp (MIL) flashes 1x long, 3x short on KTM 690 SMC EU Motorcycle?
If the FI warning lamp (MIL) on your KTM Motorcycle flashes 1x long, 3x short, it means the input signal from the intake air temperature sensor is too low or too high. Check the intake air temperature sensor.
General| Compression Ratio | 12.7:1 |
|---|---|
| Starter | Electric starter |
| Transmission | 6-speed |
| Fuel System | Electronic fuel injection |
| Cooling | Liquid cooling |
| Lubrication | Forced oil lubrication with 2 oil pumps |
| Final Drive | Chain |
| Frame | Chromium-Molybdenum steel trellis frame, powder coated |
| Suspension Travel Rear | 250 mm |
| Tires Front | 120/70 ZR 17 |
| Tires Rear | 160/60 ZR 17 |
| Chain | X-Ring 5/8 x 1/4" |
| Steering Head Angle | 63.5° |
| Seat Height | 890 mm |
| Engine Type | Single cylinder, 4-stroke engine |
| Power | 75 hp |
| Torque | 73.5 Nm |
| Clutch | Wet, multi-disc |
| Subframe | Aluminum |
| Handlebar | Aluminum, tapered |
| Front Suspension | WP USD Ø 48 mm |
| Rear Suspension | WP monoshock |
| Front Brake | Brembo four-piston radial fixed caliper, brake disc Ø 320 mm |
| Rear Brake | Brembo single piston floating caliper, brake disc Ø 240 mm |
| Wheels Front | 3.50 x 17" |
| Wheels Rear | 5.00 x 17" |
| Tank Capacity | 13.5 l |
Identifies the location of the chassis number on the vehicle.
Identifies the location of the engine number on the vehicle.
Provides safety advice and initial usage guidelines for the motorcycle.
Lists essential checks before riding the motorcycle.
Step-by-step guide for starting the motorcycle engine.
Guidelines and warnings related to motorcycle braking.
Procedure for checking the motorcycle's engine oil level.
Complete guide to oil and filter maintenance.
Diagnoses and measures for starter motor issues.
Possible causes and solutions when the engine only turns with clutch engaged.
Troubleshooting steps for when the engine cranks but won't start.
Troubleshooting steps for engine overheating issues.
Explains the FI warning light and its possible causes.
Lists diagnostic fault codes and their potential causes.
Details the engine's core specifications and configuration.
Specifies the required engine oil volume and type.
Specifies the required coolant volume and type.
Lists torque values for various engine component screws.
To Next Page