To Next PageTo Next PageHow to troubleshoot starting difficulties in a Kubota KX080-4S2 Compact Excavator?
If you're having trouble starting your Kubota Compact Excavator, it might be due to several reasons. Ensure the pilot control lock lever is in the "LOCKED" position. Also, check the fuel tank and filter for impurities and water, and replace the filter if needed. If the battery is almost dead, recharge it.
Why is my Kubota KX080-4S2 Compact Excavator overheating?
If your Kubota Compact Excavator is overheating, several factors could be the cause. Check if the coolant level is too low and fill it to the prescribed level. Inspect the radiator grill and fins for clogs and clean them if necessary. Also, a defective radiator cap can cause evaporation, so consider replacing it. Continuous operation under full load can also lead to overheating, so try to reduce the load.
What to do if the engine suddenly stops in my Kubota KX080-4S2 Compact Excavator?
If the engine of your Kubota Compact Excavator suddenly stops, check the fuel level and add fuel if necessary. Also, purge the fuel system.
Why does my Kubota KX080-4S2 Compact Excavator have low hydraulic power?
If the hydraulic system of your Kubota Compact Excavator has low power, start by checking the hydraulic oil level and add oil if it's low. Also, inspect hoses and joints for leakages, and replace any that are leaking.
Why does my Kubota Compact Excavator have abnormal exhaust gas color?
If your Kubota Compact Excavator shows abnormal exhaust gas color, it could be due to poor fuel quality. Use high-quality fuel. Alternatively, there might be too much engine oil; drain the engine oil to the prescribed level.
What causes overheating and coolant loss in a Kubota KX080-4S2?
If the water temperature in red zone (Overheating) in your Kubota Compact Excavator, and you notice coolant loss, it may be due to a damaged cylinder head gasket. Replace it.
How to restore engine power in my Kubota KX080-4S2 Compact Excavator?
If your Kubota Compact Excavator has insufficient engine power, check the fuel level and add fuel if necessary. Also, clean the air filter element, as a clogged air cleaner can cause this issue.
Why isn't the swing motor working on my Kubota KX080-4S2?
If the swing motor and front attachment of your Kubota Compact Excavator aren't working, ensure the pilot control lock lever is in the "UNLOCK" position. Bring the pilot control lock lever into the "UNLOCK" position.
Why is my Kubota KX080-4S2 deviating while driving?
If your Kubota Compact Excavator is deviating from its drive direction, check for stones blocking the system and remove them. Also, ensure the track isn't too loose or too tight and adjust it accordingly.
General| Engine Power | 65.2 hp |
|---|---|
| Operating Weight | 18, 739 lb |
| Bucket Capacity | 0.27 cu.yd |
| Max Digging Depth | 15.1 ft |
| Max Reach at Ground Level | 23 ft |
Explains safety alert symbols and their meanings (Danger, Warning, Caution).
Details pre-operation checks, safety devices like ROPS/OPG, and operator familiarization.
Covers safe operating practices, starting procedures, and working guidelines to prevent accidents.
Outlines procedures for safely parking and shutting down the excavator after use.
Provides instructions for safely loading and transporting the excavator on a vehicle.
Details safety precautions to be taken before performing maintenance work on the excavator.
Illustrates and explains various safety labels found on the excavator.
Explains how to clean, maintain, and replace safety labels.
Identifies and describes the switches and controls on the instrument panel.
Details the function and operation of the control pedals and levers.
Lists essential visual checks to be performed on the excavator before each operation.
Explains how to operate the starter switch and its functions.
Covers display selector, fuel gauge, and coolant temperature gauge readings.
Explains various warning lamps, error messages, and indicators on the panel.
Details how to set the clock, review log records, and manage periodic checks.
Explains the function of horn, light, AUX port, auto idle, throttle, and travel speed switches.
Details DPF inhibit switch, beacon light switch, and cabin controls like wipers and AC.
Instructions for handling safety devices, specifically the pilot control lock lever.
Outlines the procedure for starting the excavator's engine safely.
Provides instructions for starting in cold weather and with an auxiliary battery.
Lists critical checks to perform immediately after the engine starts.
Explains how to properly stop the engine, including overheat and DPF regeneration precautions.
Guidance on the initial 50 working hours for proper break-in of the new excavator.
Instructions on adjusting the seat and using the seat belt with ROPS/OPG.
Safety guidelines for starting, pilot lock lever, and driving the excavator.
Safe techniques for driving, including on slopes and turning.
Operation of the dozer blade and the Two Pattern Selection System.
How to operate the boom, arm, bucket, and perform unit/boom swing.
Explains the use and settings for auxiliary hydraulic ports.
Steps to safely release hydraulic system pressure.
Operation of the angle blade and selection of hydraulic circuits.
Use of boom lowering valve and explanation of the auto idle system.
Details the anti-theft device and key registration procedures.
Key operational guidelines and warnings for safe excavator use.
Steps for safely loading and securing the excavator onto a truck.
Guidelines and safety precautions for towing the excavator.
General principles, safety aspects, and procedures for lifting the machine.
Recommended lifting positions, attachment methods, and general guidelines.
Information on recommended tackle, weights, and safe lifting practices.
A table outlining maintenance checks and their intervals based on operating hours.
Details annual and biennial servicing tasks.
Procedures for replacing air conditioner parts, hoses, coolant, and fuel lines.
Describes servicing for refrigerant, DPF cleaning, and fuel filter draining.
Procedures for purging the fuel system and adjusting track tension.
Tips for operating and maintaining rubber tracks, including tension adjustment.
Procedure for changing the bucket and information on fuses.
Details on auxiliary electric, slow blow fuses, and electric fuses.
Steps to prepare the excavator for operation in cold weather conditions.
Instructions for cleaning and storing the excavator after cold weather operation.
Procedures for storing the excavator for extended periods to prevent damage.
Steps to follow when preparing the excavator for operation after long-term storage.
Specifies engine oil, fuel, and other lubricant requirements based on temperature.
Information on the use, handling, and maintenance for Biodiesel fuels.
Details oil change intervals and storage procedures for BDF.
Provides key physical dimensions of the excavator.
Details the lifting capacities of the excavator under various conditions.
Lists and describes the standard display screens on the operator panel.
Explains machine behavior and corrections for various error messages displayed on the LCD.
