Kwikset Deadbolt Series - User Manual

F
G
H
J
K (x2)
L (x2)
M (x2)
N (x2)
C D
E
BA
D
F
G
H
B
A
C
K
L
J
M
N
2⅛"
54 mm
1"
25 mm
1½"
38 mm
or • o • ou
If • Si • Si:
2⅜" (60 mm)
If • Si • Si:
2¾" (70 mm)
A
A
A
L
1
(38 mm)
Note, for a 1½" (38 mm) diameter hole,
test if latch extends and retracts. Chisel
out area if required.
Nota, para un orificio de 38 mm (1½") de
diámetro haga una prueba si el pasador
se extiende y se repliega. Cincele la zona
si asi lo requiere.
Remarque : Pour un trou de 1 1/2 po (38 mm),
s'assurer que le verrou entre et sort librement.
Au besoin, travailler la section au ciseau.
Latch
Pasador
Verrou
Interior
Interior
Intérieur
Exterior
Exterior
Extérieur
Do not use on 1½" (38 mm) holes.
No lo use en orificios de 38 mm (1½").
Ne pas utiliser sur des trous de 38 mm (1½").
D
F
G
H
B
C
K
Copyright © 2011 Stanley Black & Decker Corporation
For 1 ⅞" (48mm) to 2 " (57mm) thick
doors, refer to thick door kit.
Call toll free number for Thick Door Kit.
Para puertas de 48 mm a 57 mm (1 ⅞" a
2 ¼") de espesor, consulte el juego para
puertas gruesas. Llame al número gratuito
para el juego de puertas gruesas.
Pour les portes d’une épaisseur de 48mm
à 57mm (1⅞" à 2¼"), se reporter à
la trousse pour portes épaisses. Pour
obtenir une trousse pour portes épaisses,
composer le numéro sans frais.
Longer screws install
near door stop.
Tornillos más largos
instalan cerca de
parada de puerta.
Installer les vis
longues près de
l'arrêt de porte.
J
M
N
Parts in the Box
Piezas en la caja
Pieces dans la boîte
Tools Needed • Herramientas necesarias • Outils nécessaires
Quick Installation Guide
Guía de instalación rápida
Guide d’installation rapide
Phillips Head Screwdriver
Destornillador de cabeza de estrella
Tournevis cruciforme
Ruler
Regla
Règle
Deadbolt
26889 / 03
Check Dimensions
Revise las medidas
Vérifier les dimensions
Install Latch
Instale el pestillo
Installation du verrou
Install Strike
Instale la Placa del
Recibidor
Installez la Gâche
a
b
Install Interior and Exterior
Instale el Exterior y el Interior
Installez L’Exterieur et L’Interieur
3
1
2
4

Summary

Deadbolt Components and Tools

Parts in the Box

Lists all components included in the package for the deadbolt.

Tools Needed

Lists essential tools required for the installation process.

Deadbolt Installation Procedures

Check Dimensions and Install Latch

Verify door dimensions and install the deadbolt latch mechanism.

Install Interior and Exterior Components

Mount the interior and exterior parts of the deadbolt lock.

Install Strike Plate

Install the strike plate on the door jamb to receive the bolt.

Drilling and Preparation Instructions

Drilling Template and Tools

Provides a template and lists tools for marking and drilling door holes.

Door Bore and Latch Preparation

Instructions for drilling door bores and preparing the latch face.

Strike Plate Hole Marking and Preparation

Mark and prepare the door jamb for the strike plate installation.

Kwikset Deadbolt Series Specifications

General

Type	Deadbolt
Compatibility	Standard doors
Backset	2-3/8" or 2-3/4"
Door Thickness	1-3/8" to 1-3/4"
Bolt Throw	1"
Finish Options	Satin Nickel, Venetian Bronze, Polished Brass
Keyway	KW1
Security Features	Anti-pick pins
Material	Metal
Installation	DIY or Professional