Kyocera ECOSYS FS-C8520MFP Technical Reference Manual

Chapter 7 Emulation
7-42
Switching the Print Resolution
Because the printing systems with the 1200 dpi resolution support print at 300, 600, 1200
dpi, the printing system provides an FRPO command to establish a default at either level
of resolution.
For fine 1200 dpi resolution, command:
!R! FRPO N8, 3; EXIT;
For 600 dpi resolution, command:
!R! FRPO N8, 1; EXIT;
For 300 dpi resolution, command:
!R! FRPO N8, 0; EXIT;
When the printing resolution is changed between 1200 dpi, 600 dpi, and 300 dpi, the
printing system loads the PJL current environment values.
In addition to the FRPO N8 command as explained above, printing systems that permit
the resolution to be set at either 300, 600, or 1200 are provided with the RESL (change
RESoLution) command which switches the resolution on the fly. For details about this
command, refer to PRESCRIBE Commands Command Reference.
Note
The amount of available printing system memory will determine whether the 600/1200 dpi
default can be effective. If factors such as resource protection, duplexing, and raster mem-
ory reduce memory too low, then the printing system will remain at 300 dpi resolution.
HPLJ 4, duplex mode=on, raster memory=Legal 3 Mbytes 11 Mbytes
HPLJ 4/KPDL, duplex mode=None, raster memory=A4/Letter 2 Mbytes 6 Mbytes
HPLJ 4/KPDL, duplex mode=None, raster memory=Legal 2 Mbytes 7 Mbytes
HPLJ 4/KPDL, duplex mode=on, raster memory=A4/Letter 3 Mbytes 10 Mbytes
HPLJ 4/KPDL, duplex mode=on, raster memory=Legal 3 Mbytes 11 Mbytes
HPLJ 4/KPDL, resource protection, duplex mode=None 10 Mbytes 10 Mbytes
HPLJ 4/KPDL, resource protection, duplex mode=on 14 Mbytes 14 Mbytes
Table 7.21. Example: FS-9500DN
Printing Condition Resolution
300 dpi 600 dpi 1200 dpi
Fast mode Fine mode
PCL 6, duplex mode=None 8 MB 8 MB 8 MB 8 MB
PCL 6, duplex mode=On 8 MB 8 MB 8 MB 12 MB
KPDL, duplex mode=None 8 MB 8 MB 8 MB 8 MB
KPDL, duplex mode=On 8 MB 8 MB 12 MB 12 MB
PCL 6/KPDL resource protection,
duplex mode=None
— 10 MB 10 MB 10 MB
PCL 6/KPDL, resource protection,
duplex mode=On
— 14 MB 14 MB 14 MB
Table 7.20. Example: FS-1000 Series
Printing Condition Resolution
300 dpi 600 dpi

Kyocera ECOSYS FS-C8520MFP Specifications

General

Category	Printer
Type	Multifunction Printer
Functions	Print, Copy, Scan, Fax
Print Technology	Laser
Print Speed (B/W)	20 ppm
Print Speed (Color)	20 ppm
Max Print Speed (B/W)	20 ppm
Max Print Speed (Color)	20 ppm
Print Resolution	600 x 600 dpi
Max Print Resolution	9600 x 600 dpi
Max Paper Size	A3
Duplex Printing	Yes
Scanner Type	Flatbed, ADF
Scan Resolution	600 x 600 dpi
Duplex Scanning	Yes
Copy Resolution	600 x 600 dpi
Fax	Yes
Supported Paper Sizes	A3, A4, A5, A6, B5, Letter, Legal
Monthly Duty Cycle	65000 pages
Max Paper Capacity	1600 sheets
Memory	1 GB
Connectivity	USB, Ethernet
Copier Speed (B/W)	20 ppm
Copier Speed (Color)	20 ppm
Copy Speed (B/W)	20 ppm
Copy Speed (Color)	20 ppm
Display	4.3-inch touch screen