How to troubleshoot a Kyocera FS-1128MFP that cannot print?
If your Kyocera All in One Printer cannot print, check the following: * Ensure the power cord is plugged into an AC outlet. * Verify the main power switch is turned on. * Make sure the printer cable is securely connected. * Ensure the machine was powered on after connecting the printer cable. * If the print job is paused, press [Resume] to resume printing.
What to do if my Kyocera FS-1128MFP All in One Printer is printing dirty?
Dirty printouts from your Kyocera All in One Printer can be caused by a dirty platen or document processor; clean them. Alternatively, the charger wire may be dirty; clean the charger wire.
Why does my Kyocera Printer paper often jam?
Paper jams in your Kyocera printer can occur for several reasons. Ensure the paper is loaded correctly. The paper may be an unsupported type or in poor condition, so try removing it, turning it over, and reloading it. If the paper is curled, folded, or wrinkled, replace it with new paper. Also, check for and remove any loose scraps or jammed paper inside the machine.
What to do if my Kyocera All in One Printer prints blank sheets?
If your Kyocera All in One Printer is ejecting blank sheets, it might be due to the originals being loaded incorrectly. If using the platen, place the originals face-down and align them with the original size indicator plates. If using the optional document processor, place the originals face-up.
Why does my Kyocera FS-1128MFP All in One Printer paper often jam?
Paper jams can occur in your Kyocera All in One Printer for several reasons: * The paper may not be loaded correctly. * The paper might be an unsupported type or in poor condition; try turning it over and reloading it. * The paper could be curled, folded, or wrinkled; replace it with new paper. * There may be loose scraps or jammed paper inside the machine; remove any jammed paper.
Why my Kyocera FS-1128MFP All in One Printer cannot output from a Sub Address Box?
If your Kyocera All in One Printer cannot output from a Sub Address Box, it may be because the box password has been set. Enter the correct box password to access the output.
What to do if my Kyocera FS-1128MFP displays 'The phone receiver is off the hook.'?
If your Kyocera All in One Printer displays 'The phone receiver is off the hook', check if the phone connected to the machine is off the hook. If it is, hang up the handset.
Why my Kyocera All in One Printer cannot store memory forwarding data in a Sub Address Box?
Your Kyocera All in One Printer may fail to store memory forwarding data in a Sub Address Box because: * The Sub Address Box may not be specified correctly. Check the memory forwarding setting. * There may not be enough free space available in the memory. Receive after the memory has free space, or create free space in the memory.
Why my Kyocera FS-1128MFP All in One Printer cannot perform memory forwarding?
If your Kyocera All in One Printer cannot perform memory forwarding, check the memory forwarding setting to ensure it is set to [On].
Why my Kyocera All in One Printer cannot perform sub address transmission?
Your Kyocera All in One Printer may fail to perform sub address transmission due to these reasons: * The recipient fax machine may not be equipped with a sub address transmission feature. Sub address transmission cannot be performed unless the recipient fax machine has a similar sub address transmission feature. * The entered sub address or sub address password may not be identical to the sub address or sub address password registered in the recipient fax machine. If your entry is correct, check with the recipient. * There may not be enough free space available in the memory of the recipient fax machine. Check with the recipient.
General| Duplex printing | Yes |
|---|---|
| Print technology | Laser |
| Maximum resolution | 1200 x 1200 DPI |
| Time to first page (black, normal) | 6 s |
| Print speed (black, normal quality, A4/US Letter) | 28 ppm |
| Printing colors | Black |
| Maximum duty cycle | 20000 pages per month |
| Page description languages | PCL 5e, PCL 6, PCL XL |
| Scan to | FTP |
| Grayscale levels | 256 |
| Image formats supported | JPG, TIF |
| Optical scanning resolution | - DPI |
| Copier resize | 25 - 400 % |
| Maximum copy resolution | 600 x 600 DPI |
| Maximum number of copies | 999 copies |
| Time to first copy (black, normal) | 6.9 s |
| Faxing | Mono faxing |
| Fax memory | 100 pages |
| Modem speed | 33.6 Kbit/s |
| Fax coding methods | JBIG, MMR (Fax coding method), MR |
| Fax transmission speed | 3 sec/page |
| Total input capacity | - sheets |
| Total output capacity | 150 sheets |
| Maximum input capacity | 800 sheets |
| Internal memory | 256 MB |
| Processor model | 440 |
| Processor family | PowerPC |
| Maximum internal memory | 768 MB |
| Sound power level (standby) | 30 dB |
| Sound pressure level (copying) | 52 dB |
| Custom media sizes | 105 x 148mm/216 x 356mm |
| Dimensions (WxDxH) | 494 x 410 x 366 mm |
| Power requirements | AC 220 - 240 V, 50/60Hz |
| All-in-one functions | Copy, Fax, Scan |
| Color all-in-one functions | scan, n |
| Compatible operating systems | Windows 2000/XP/Server 2000/Server 2003/ Vista/Server 2008, MAC OS 9.X, MAC OS X, Linux |
| Maximum print size | 216 x 356 mm |
| Duplex media weight | 60 - 105 g/m² |
| Paper tray media types | Envelopes |
| Paper tray media weight | 60 - 120 g/m² |
| Non-ISO print media sizes | Folio |
| ISO A-series sizes (A0...A9) | A4, A5, A6 |
| ISO B-series sizes (B0...B9) | B5 |
| Maximum ISO A-series paper size | A4 |
| Multi-Purpose Tray media weight | 60 - 220 g/m² |
| Standard interfaces | USB 2.0 |
| USB 2.0 ports quantity | 1 |
| Power consumption (standby) | 91 W |
| Power consumption (PowerSave) | 10.2 W |
| Power consumption (average operating) | 494 W |
| Certification | TÜV/GS, CE |
| Display | - |
| Market positioning | Business |
| Supported network protocols (IPv6) | SNMPv3, SSL, IPsec |
| Sustainability certificates | ENERGY STAR |
| Harmonized System (HS) code | 84433100 |
To Next Page
