Why do copies come out blank on my Kyocera All in One Printer?
If you're getting blank copies from your Kyocera All in One Printer, check the originals. When using the platen, ensure the originals are placed face-down. If you are using the optional Document Feeder (DF), make sure the originals are placed face-up.
Why are my Kyocera KM-1530 All in One Printer copies too light?
If your copies are too light, several factors could be the cause. First, if the copier is in auto exposure mode, try performing the auto exposure adjustment. If it's in Text & Photo, Photo, or Text mode, adjust the exposure using the copy exposure adjustment keys or perform the exposure adjustment for that specific mode. Also, check if the 'Add Toner' indicator is lit, and if so, replace the toner cartridge. Finally, ensure the paper isn't wet; if it is, replace it with new paper.
What to do if my Kyocera KM-1530 All in One Printer copies are too dark?
If your copies are too dark, and the copier is in auto exposure mode, perform the auto exposure adjustment. If it is in Text & Photo, Photo, or Text mode, adjust the exposure to the correct degree using the copy exposure adjustment keys. You can also perform the exposure adjustment for the Text & Photo, Photo, or Text mode to change the overall exposure.
How to fix misfeeds on Kyocera KM-1530 All in One Printer?
To address frequent misfeeds, ensure the paper is correctly set in the drawer(s). Replace any curled, folded, or wrinkled paper with new paper. Also, check inside the copier for any misfed paper or loose scraps and remove them.
Why is the copy image askew on my Kyocera KM-1530 All in One Printer?
If the copy image is askew, check how you're setting the originals. When using the platen, align their edges with the correct original size scale. If using the optional DF, adjust the original insertion guides to the correct size of the originals.
Why are my Kyocera KM-1530 All in One Printer copies dirty?
If your copies are coming out dirty, the platen or original cover might be dirty. Clean the platen and/or the original cover. Additionally, open the front cover and pull and push back in the cleaning shaft.
What to do if copied sheets are not stored tidily in the copy store section of my Kyocera KM-1530?
If copied sheets are not stored tidily, it could be because the copied sheets are curled. Remove the paper from the drawer or multi-bypass used and turn the paper upside down.
What to do if nothing lights up on the operation panel of my Kyocera KM-1530?
If nothing lights up on the operation panel when the main switch is turned on, connect the plug to an AC outlet.
Power| voltage | 120 V |
|---|---|
| current | 9A |
| operating noise level | 55 dB |
Memory| optional memory | 32 MB or 64 MB |
|---|---|
| page memory capacity with 32 MB | 79 Letter Size Pages at 6% Image Area |
| page memory capacity with 64 MB | 250 Letter Size Pages at 6% Image Area |
Printing and Copying| resolution | 600 x 600 dpi |
|---|---|
| grayscale levels | 256 Levels |
| multi copy speed without memory board | 15 CPM Invoice and Letter, 8 CPM Legal, 8 CPM Ledger |
| multi copy speed with memory board | 18 CPM Invoice and Letter, 10 CPM Legal, 9 CPM Ledger |
Paper Handling| paper weight drawers | 17-22 lbs. Bond, 35-45 lbs. Index |
|---|---|
| paper weight bypass | 12-42 lbs. Bond, 25-88 lbs. Index |
| minimum/maximum paper size | 5.5" x 8.5"/11" x 17" |
Weight and Dimensions| width | 22" |
|---|---|
| depth | 22" |
| height | 18" |
| weight | 86 lbs. |
Details about copy speed, paper types, and sizes for the 15 cpm copier.
Identifies and describes key components of the copier and operation panel.
Procedures and codes for diagnosing and resolving paper misfeed errors.
Details the self-diagnostic functions and error codes for the machine.
Lists common image quality issues and their potential causes and solutions.
Troubleshoots issues related to the machine's electrical components and power.
Addresses mechanical faults, jams, and operational issues.
Safety and procedural guidelines before performing assembly or disassembly.
Steps for replacing the main printed circuit board in the machine.
Instructions for updating the firmware on the main control board.
Instructions for updating firmware on the operation panel PCB.
To Next Page
