Why can't my Kyocera KM-5050 All in One Printer receive documents?
There are several reasons why your Kyocera All in One Printer might not be able to receive a document: * The modular cord may not be connected correctly. Connect it correctly. * A communication error may be occurring. Remedy the cause of the error and ask the sender to retry. * The RX (reception) restriction may be activated. Cancel the RX restriction.
What to do if Kyocera KM-5050 All in One Printer FAX box limit exceeded?
The FAX Box capacity is full with document data. Press [OK]. The job is canceled. To resolve this, try the job again after printing or deleting the data in the FAX Box.
What to do if Kyocera KM-5050 All in One Printer cannot perform memory reception?
To resolve the issue, receive after the memory has free space, or create free space in the memory.
What to do if Kyocera KM-5050 All in One Printer cannot perform broadcast transmission?
This issue occurs when there isn't enough free space available in the memory. To resolve this, send after the memory has free space, or create free space in the memory.
What to do if Kyocera KM-5050 says phone is off the hook?
If the phone (commercially available) connected to the machine is off the hook, hang up the handset.
Why can't I use the remote switching function on my Kyocera All in One Printer?
This can happen for a couple of reasons: * A pulse line might be in use. Some phones may transmit tone signals using buttons. Refer to the operation manual of your phone set. * The remote switching number might not be correct. Check the registration. (Default: 55)
What to do if Kyocera KM-5050 All in One Printer cannot perform encrypted communication?
Double-check the registrations both at sender and recipient to ensure they are correct.
What to do if Kyocera All in One Printer cannot use sub address relay broadcast communication?
This problem arises when there isn't enough free space available in the memory. To resolve this, free up some space in memory and then send, or simply make some free space in memory.
Why can't my Kyocera All in One Printer perform memory forwarding?
This issue occurs if memory forwarding is not set to [On]. Check the memory forwarding setting.
Why can't my Kyocera KM-5050 All in One Printer perform memory forwarding using a sub address?
This issue can occur for the following reasons: * The recipient fax machine may not be equipped with a sub address transmission feature. Sub address transmission cannot be performed unless the recipient fax machine has a similar sub address transmission feature. * The entered sub address may not be identical to the sub address registered in the recipient fax machine. If your entry is correct, check with the recipient. This machine does not use a sub address password for reception.
General| electrical requirements | 120V, 60Hz, 11.5A |
|---|---|
| max monthly volume | 200, 000 Pages Per Month |
| warm-up time | Within 30 Seconds |
| first copy out | 3.5 Seconds |
| pages per minute | 50 Letter, 26 Legal, 26 Ledger |
| system memory | Standard 512MB RAM, upgradeable to 1GB |
| hard disk drive | Standard 80GB HDD |
| resolution | 600 x 600 DPI |
| standard paper sources | Dual 500 Sheet Drawers, 200 Sheet MPT |
| drawer paper size | 5.5" x 8.5" - 11" x 17" |
| paper weight | 13-28 lb Bond via Paper Drawers, 13 lb Bond -110 lb Index via MPT |
| paper size | 5.5" x 8.5" – 11" x 17" |
| paper weight | 17 – 20 lb Bond |
| capacity | 100 Sheet DSDP / 50 Letter Size Originals Per Minute |
| dimensions | 22.4”W x 20.7”D x 5.9”H |
| weight | 29 lbs |
| stack capacity | Main Tray (A): 3, 000 Sheets; Sub Tray (B): 200 Sheets, Sub Tray (C): 50 Sheets |
| dimensions | 26.9"W x 22.2"D x 42.8"H |
| weight | 121 lbs |
| number of trays | 7 |
| dimensions | 20.1"W x 15.7"D x 18.5"H |
| weight | 22 lbs |
| weight | 6.6 lbs |
| dimensions | 25.9"W x 17.9”D x 10.5"H |
| weight | 53 lbs |
| dimensions | 22.0"W x 20.7"D x 36.0"H |
| weight | 55 lbs |
| dimensions | 12.2”W x 16.1”D x 6.3”H |
| weight | 19.8 lbs |
| dimensions | 23.0”W x 23.6”D x 12.4”H |
| weight | 50.7 lbs |
| dimensions | 23.0”W x 23.2”D x 12.4”H |
| weight | 57.3 lbs |
Weight and Dimensions| dimensions | 23.6"W x 25.4"D x 29.3"H |
|---|---|
| weight | 188 lbs |
Identifies key external parts of the machine and their functions.
Details the screens and options within the FAX send interface.
Explains the step-by-step process for sending faxes automatically.
Provides methods to cancel ongoing or scheduled FAX transmissions.
Guides on how to add new contacts or groups to the address book.
Explains how to assign destinations to one-touch keys.
Outlines destination types and criteria for forwarding received faxes.
Explains remote configuration of memory forwarding via COMMAND CENTER.
Specifies settings for receiving and forwarding faxes.
Guides on adding new destinations for fax forwarding.
Explains the purpose and use of FAX Boxes for storing received faxes.
Guides on accessing and viewing the job log screen.
Guides on how to view detailed information for each job log entry.
Guides on setting up automatic switching between FAX and TEL.
Configures settings to restrict outgoing transmissions.
Sets up lists to reject incoming faxes.
Guides on registering FAX numbers that are allowed to transmit.
Describes encryption key settings for secure fax communication.
Guides on accessing the send screen for initiating i-FAX transmissions.
Initiates the FAX transmission process after settings are configured.
Guides on how to manually check for and receive incoming i-FAXes.
To Next Page
