To Next PageTo Next PageHow to fix 'OFL' appearing in the indoor temperature section of my La Crosse Technology WS-8117?
If 'OFL' appears in the indoor temperature section of your La Crosse Technology Clock, move the clock to an area with a warmer or cooler surrounding temperature. The current surrounding temperature is outside the measuring range.
How to fix a faint LCD on my La Crosse Technology WS-8117 Clock?
If the LCD on your La Crosse Technology Clock is faint, replace the batteries.
What to do if my La Crosse Technology Clock isn't receiving the WWVB signal?
If your La Crosse Technology Clock isn't receiving the WWVB signal, try the following: * Face the front of the clock towards Ft. Collins, Colorado, to improve reception. * Allow the clock to attempt signal reception overnight. * Ensure the clock is at least 6 feet (2 meters) away from electronic devices like TVs, computers, or other radio-controlled clocks. * Remove the batteries for five minutes, then reinsert them, leaving the unit undisturbed overnight without pressing any buttons.
What to do if '--.-' appears on my La Crosse Technology WS-8117 Clock's outdoor temperature display?
If you see '--.-' in the outdoor temperature section of your La Crosse Technology Clock's display, try these steps: 1. Remove the batteries from both the clock and the transmitter for one minute, then reinsert them, ensuring they are new. 2. Move the clock closer to the transmitter, or vice versa, making sure they are within receivable range. 3. Relocate both units to avoid interference from other electrical devices operating on the same frequency (433MHz).
Why is the hour incorrect on my La Crosse Technology Clock when the minute and date are correct?
If the hour is incorrect on your La Crosse Technology Clock, but the minute and date are correct, ensure that you have selected the correct time zone and daylight saving time settings.
What to do if 'OFL' appears in the outdoor temperature section of my La Crosse Technology WS-8117 Clock?
If 'OFL' is displayed in the outdoor temperature section of your La Crosse Technology Clock, it indicates that the current surrounding temperature is outside the measuring range of the transmitter. Wait for the temperature to cool down or increase until it is within the transmitter's range. The outdoor temperature will reappear on the display once the temperature is within the specified range.
General| Display | LCD |
|---|---|
| Time Display | 12/24 hour |
| Atomic Time Signal | WWVB |
| Type | Atomic Clock |
| Power Source | 2 AA batteries |
| Features | Atomic time, Indoor temperature, Calendar |
| Time Zone | Selectable time zones |
Lists features of the atomic clock, including time display, alarm, calendar, and temperature settings.
Describes the outdoor temperature transmitter and its remote transmission capability.
Instructions for installing and replacing batteries in the atomic clock unit.
Instructions for installing and replacing batteries in the outdoor temperature transmitter.
Explains the function of the SET key for entering set modes and navigating settings.
Describes the use of the + key for changing values and toggling displays.
Explains the function of the ALM key for entering alarm mode and setting alarm ON/OFF.
Details the SNZE key's function for snooze during alarm and exiting settings.
Procedure to set the year from 2000 to 2049.
Procedure to set the current month.
Procedure to set the current date, considering the selected month.
Procedure to set the current day of the week.
Selection between 12-hour and 24-hour time display formats.
Selection between Celsius (°C) and Fahrenheit (°F) for temperature display.
Steps to set the alarm time and activate/deactivate it.
Instructions on how to turn off an active alarm.
How to activate the snooze function when the alarm sounds.
Details on how to position the atomic clock using table stands or wall mounting.
Instructions for extending and using the foldable table stand.
Steps for mounting the atomic clock to a wall using screws.
Instructions for mounting the transmitter using screws.
Instructions for mounting the transmitter using adhesive tape.
Solutions for faint LCD, 'OFL' indoor/outdoor, and '--.-' outdoor temperature readings.
Steps to troubleshoot and improve WWVB signal reception.
Addresses issues with incorrect hour display, suggesting time zone/DST checks.
