Launch KES-200 User Manual

LAUNCH KES-200 General Information
A-1
General Information
Table of Contents
General Information································· A-1
Introduction of Main Unit··························· A-2
Outline of KES-200······························ A-2
Keypad ············································· A-2
Specifications········································· A-2
Main Unit··········································· A-2
Oscilloscope······································· A-2
Multimeter·········································· A-3
Ignition Waveform································ A-3
Starting System Analysis······················· A-3
Charging System Analysis····················· A-3
System Setting ··································· A-3
Configuration List···································· A-3
Configuration List ································ A-3
Main Parts Instruction··························· A-3
System Setting ······································· A-5
Update·················································· A-5

Launch KES-200 Specifications

General

Brand	Launch
Model	KES-200
Category	Test Equipment
Language	English

Summary

General Information

Introduction of Main Unit

Describes the physical components of the KES-200 unit.

Specifications

Lists technical specifications for the main unit and oscilloscope function.

Configuration List

Details all included accessories, parts, and their quantities.

Main Parts Instruction

Explains how to connect essential cables for operating the KES-200.

System Setting

Guides users on configuring language, sound, and other system parameters.

Update

Describes procedures for updating the KES-200 software via the internet.

4Channel Oscilloscope

Brief Introduction

Provides a general overview of the oscilloscope's capabilities and features.

Specifications

Lists technical specifications for the oscilloscope function of the KES-200.

Connection

Explains how to connect the necessary oscilloscope cables to the unit.

Configuration of Oscilloscope Function

Details how to set up and configure the oscilloscope modes and settings.

Getting Started

Provides initial steps and guidance to begin using the oscilloscope function.

How to Enter Oscilloscope

Step-by-step guide to access the oscilloscope mode from the main menu.

Multimeter

Brief Introduction

Introduces the multimeter function and its applications for automotive diagnostics.

Specifications

Lists the measuring ranges and specifications for various multimeter functions.

Getting Started

Provides initial setup and access instructions for using the multimeter.

How to Enter

Details how to access the multimeter mode from the KES-200 main menu.

Voltage Measuring

Explains the procedure and connection for measuring voltage.

Current Measuring Mode

Explains the procedure and connection for measuring current.

Resistance Measuring Mode

Explains the procedure and connection for measuring resistance.

Frequency Measuring Mode

Explains the procedure and connection for measuring frequency.

Duty Cycle Measuring Mode

Explains the procedure and connection for measuring duty cycle.

Battery Volt Measuring Mode

Explains how to measure battery voltage.

Tachometer Measuring Mode

Explains how to measure engine RPM using the multimeter.

Intake Manifold Vacuum (Optional)

Explains how to measure intake manifold vacuum.

Ignition Waveform

Brief Introduction

Introduces the ignition waveform analysis capability of the KES-200.

Purpose of Waveform Analysis

Explains the benefits and use of analyzing ignition waveforms for diagnostics.

Components and Accessories for Measuring Primary/Secondary Ignition Waveform

Lists all necessary parts for ignition waveform testing.

Getting Started

Provides initial steps for setting up and performing ignition waveform analysis.

How to Setup

Guides on the initial setup procedures for ignition waveform tests.

Description of Ignition Mode

Explains different ignition modes like DLI and Distributor.

Connections for Different Tests

Details specific cable connections for various ignition waveform tests.

Starting System Analysis

Specification

Lists the measuring scope for starting voltage and current tests.

How to Start

Describes the initial steps to begin a starting system analysis.

Starting Voltage

Explains how to test battery voltage during engine start.

Starting Current

Explains how to test battery current during engine start.

Charging System Analysis

Specifications

Lists the measuring scope for charging system voltage and current.

How to Start

Describes the initial steps to begin a charging system analysis.

Cylinder Analysis

Specifications

Lists the applicable functions and their respective measuring scopes.

How to Start

Describes the initial steps to access the cylinder analysis functions.

Power Balance

Explains the procedure for performing a power balance test on engine cylinders.

Units and Parts Required

Lists the necessary equipment for conducting power balance tests.

Connection

Details the specific cable connections required for power balance testing.

Operation Procedures

Guides users through the steps to perform a power balance test.

Cylinder Efficiency

Explains the process and methodology for cylinder efficiency testing.

Relative Compression

Describes how to perform a relative compression test on engine cylinders.

PC Link

System Requirement

Outlines the necessary PC hardware and software for PC Link functionality.

Software Installation

Provides step-by-step instructions for installing the PC Link software.

Connection

Explains how to physically connect the KES-200 to the PC.

Main Interface of PC Link

Describes the layout and elements of the PC Link software's main screen.

Oscilloscope Function

Details how to upload and view oscilloscope waveforms on the PC.

Ignition Function

Details how to upload and view ignition waveforms on the PC.