LeeBoy 8500 - Auger and Screed Controls; Auger Extension Use; Hydraulic Cutoff Procedures

117 pages

Save Page as PDF

To Next Page

To Previous Page

Main Page

Index4
Rear View6
Front 3/4 View6
Important Safety Instructions7
Safety Precautions8
Specifications9
Pre-Start Inspection10
Stopping Safety10
Maintenance Safety10
Operating Safetey10
Controls and Descriptions12
Stopping the Engine13
Paver Driving Instructions13
Preliminary13
Starting the Engine13
Truck Hitch Attachment14
Paving Preparation Instructions15
Burner Ignition Procedures15
If Burners Don't Ignite15
Manual Lighting of Burners16
Operating Feeder17
Operation of Electric Flight Screws18
Use of Auger Extensions18
Operation of Hydraulic Cutoffs19
Automatic Auger19
Electric Spraydown19
How to Operate20
Automatic Augers: New Style20
Loading21
Unloading21
Tie down Procedure22
Wrong Loading22
Paver Loaded Position22
Paver Preparation Instructions23
Starting to Pave23
Setting Screed to Pave24
Setting Screed Endgates25
Setting Screed Extensions26
Paver Operation26
After the First 50 Hour and Weekly Routine Maintenance27
10-Hour or Daily Routine Maintenance27
Routine Maintenance27
100 Hour or Monthly Routine Maintenance28
250 Hour or Quarterly Routine Maintenance29
500 Hour or Semi-Annual Routine Maintenance29
1000 Hour or Annual Routine Maintenance29
Lubrication Chart30
Maintenance Adjustments31
To Raise Feeders31
Lowering Feeder32
Feeder Flight Chain Adjustment32
Automatic Track Adjustment32
Sprocket Drive Undercarriage Adjustments34
Low Gear35
Directional Control Adjustment35
Torque Hub Hydraulic Motor Adjustment35
Feeder Drive Chain35
Conveyor Limit Switch36
Limit Swtich Adjustment36
Trouble Shooting Guide41
How to Override Hatz Fuel Solenoid Valve43
Track Tension Pressure43
How to Release Track Tension44
Track Component Replacement44
How to Remove Torque Hub45
How to Replace Rear Conveyour Shaft46
How to Replace Augers and Inner Bearings47
Screed Service and Information47
How to Change Screed Wearplate48
How to Adjust Top Guides on Extensions48
How to Change Screed Extensions, Slides or Bushings48
How to Change Extension Wearplates49
Table of Contents51
List of Illustrations51
Sprocket Drive Track System52
Conveyor Drive Assembly54
Hopper Components (Low Deck)56
Hopper Components (High Deck)58
Auger Assembly60
Conveyor Drive Cutoff, Screed Lift Cylinders62
Hydraulic Components L/H Side64
- Special Components L/H Side66
- Special Components L/H Side with Tst Dash68
R/H Drive & Fuel Tank70
Pump Components Sundstrand72
Pump Components Sundstrand Electronic Steering74
Hydraulic Pump and Control Assembly76
Engine and Pump Components78
Main Valve and Spray down80
- Filter Location & Accessories82
- Seat, Walkway & Other Components84
- Expandable Screed Assembly88
Vibrator Assembly92
Jointer Assembly94
Screed Arm Assembly with Center Toe Point96
Propane Heater & Automatic Ignitors98
Auger Extension 24”100
Auger Extension 24101
Paver Leveling Control102
Paver Grade Controls Spectra Physics104
Truck Hitch Assembly106
- Umbrella108
- Assembly Instructions108
Elite III Sheet Metal Cover110
Strike Offs & Extensions112
Elite III Valve114
Elite III Dash116

LeeBoy 8500 - Auger and Screed Controls; Auger Extension Use; Hydraulic Cutoff Procedures

Table of Contents

Related product manuals