Leuze electronic BCL 8 Series User Manual (English)

Other manuals for Leuze electronic BCL 8 Series

Questions and Answers:

J
Janet PetersenAug 18, 2025
What to do if Leuze electronic Barcode Reader cannot read code?
- J
  Jessica GuzmanAug 18, 2025
  If your Leuze electronic Barcode Reader fails to read codes, it could be due to several reasons. First, ensure the code quality is sufficient and that the entire code is within the laser line. Second, verify that the code is enabled in the code table, checking the type and length entries. Finally, address excessive reflections by increasing the angle of the laser beam to more than 10° with respect to vertical.
C
Christopher PenaAug 20, 2025
Why is no communication possible with Leuze electronic Barcode Reader?
- J
  Jennifer MarshallAug 21, 2025
  If you are experiencing communication issues with your Leuze electronic Barcode Reader, there are several potential causes. First, verify the wiring to ensure it is correct. Second, confirm that the correct interface is selected using the BCLconfig tool. Lastly, check the protocol settings in both the BCL 8 and the BCLconfig tool, or switch the BCL 8 to service mode to ensure they are aligned.
J
jonathan16Aug 22, 2025
How to fix Leuze electronic Barcode Reader when status LED is flashing red?
- M
  Michael CooperAug 23, 2025
  If the status LED on your Leuze electronic Barcode Reader is flashing red, this indicates a device warning. To resolve this, query the diagnostic data within the device and take the necessary actions based on the results, or try resetting the device.
K
Kenneth AnthonyAug 26, 2025
What to do if Leuze electronic Barcode Reader status LED is flashing orange?
- M
  Melanie BlackAug 26, 2025
  If the status LED on your Leuze electronic Barcode Reader is flashing orange, it means a service operation is currently active. You can reset this by either resetting the device or interrupting the supply voltage.
S
Shelby OliverAug 28, 2025
Why is the status LED on my Leuze electronic Barcode Reader continuous red?
- C
  Carol HarrisonAug 28, 2025
  If the status LED on your Leuze electronic Barcode Reader shows a continuous red light, it indicates a serious internal error that prevents the device from functioning. In this case, send the device in for testing.
N
nicholasgallegosAug 30, 2025
How to troubleshoot Leuze electronic Barcode Reader when status LED is off?
- N
  naguilarAug 30, 2025
  If the status LED on your Leuze electronic Barcode Reader is off, it indicates that no supply voltage is connected to the device. Check the supply voltage to resolve this issue.
J
Jeremy HowardSep 1, 2025
What to do if Leuze electronic Barcode Reader has no communication?
- T
  Troy CrossSep 2, 2025
  If your Leuze electronic Barcode Reader isn't communicating, there are several potential causes. First, check the wiring to ensure it is correct. Second, verify that the correct interface is selected in the BCLconfig tool. Finally, confirm that the protocol settings in the BCL 8 and BCLconfig tool match, or switch the BCL 8 to service mode.
C
carolinesanchezSep 4, 2025
Why is my Leuze electronic BCL 8 Barcode Reader not reading codes?
- B
  Brian PhillipsSep 5, 2025
  If your Leuze electronic Barcode Reader isn't reading codes, consider these potential causes: the code quality might be insufficient, so improve the code quality and ensure the entire code is within the laser line. Also, the code might not be enabled, so check the entries in the code table (type and length). Finally, excessive reflections could be the issue, so increase the angle of the laser beam to more than 10° with respect to vertical.
L
Lisa GarciaSep 6, 2025
What does it mean if the status LED is flashing red on Leuze electronic BCL 8 Barcode Reader?
- T
  Timothy NovakSep 6, 2025
  If the status LED on your Leuze electronic Barcode Reader is flashing red, it indicates a device warning. To resolve this, query the diagnostic data in the device, take the necessary actions based on the findings, or try resetting the device.
L
Lindsay WhiteSep 9, 2025
How to fix Leuze electronic BCL 8 when status LED is flashing orange?
- A
  Anna ColemanSep 9, 2025
  If the status LED on your Leuze electronic Barcode Reader is flashing orange, it means a service operation is active. You can reset the service operation by resetting the device or interrupting the supply voltage.

Leuze electronic BCL 8 Series Specifications

General

Series	BCL 8
Manufacturer	Leuze electronic
Interface	RS-232, RS-422, RS-485, Ethernet
Operating Temperature	0°C to +50°C
Protection Class	IP65
Light source	LED
Power Supply	10-30 V DC