Lexicon DC-2 User Manual (English)

Other manuals for Lexicon DC-2

Owner's Manual67 pages

Quick Reference Guide2 pages

Questions and Answers:

W
William JohnsonAug 15, 2025
What to do if Lexicon DC-2 Recording Equipment has no output?
- J
  John SmithAug 15, 2025
  If your Lexicon Recording Equipment isn't producing any output, there are several things to check: * First, ensure that a signal is actually reaching the DC-2. You can verify this via the Status menu (accessed by pressing and holding Record/Zone 2 on the remote, then pressing OSD ON), which displays input level meters and sample rate. * Next, increase the volume using the remote and check the Front/Back and Left/Right balance. * Also, confirm that the DC-2 MUTE controls are disengaged. * Verify all other equipment settings and connections, ensuring that the amplifiers connected to the DC-2 are working. * Finally, remember that the DC-2 mutes the output to any speakers not configured in the Setup menu. Adjust the Speaker Configuration menu if you've added or removed speakers.
J
Joshua BrockAug 18, 2025
How to fix Lexicon DC-2 Recording Equipment remote control not working?
- C
  Crystal LewisAug 19, 2025
  If the remote control for your Lexicon Recording Equipment is not working, start by checking the batteries. Ensure they are inserted correctly, paying attention to the proper polarity. Also, make sure that nothing is blocking the infrared sensor on the DC-2 front panel.
K
Kaitlyn JohnsAug 21, 2025
How to troubleshoot Lexicon DC-2 Recording Equipment power does not come on?
- S
  Sean ChenAug 21, 2025
  If your Lexicon Recording Equipment isn't powering on, check the line cord to ensure it's securely connected to both the AC outlet and the receptacle on the DC-2 rear panel. Also, verify that the power switch on the DC-2 rear panel is in the ON position.
D
deleonmarkAug 26, 2025
What to do if Lexicon Recording Equipment has no audio?
- D
  Douglas ContrerasAug 26, 2025
  If you're not getting any audio from your Lexicon Recording Equipment, check the Status menu. You can find it under DISPLAY ADJUST: ON-SCREEN or FRONT PANEL menu — or by pressing and holding Record/Zone 2 on the remote and pressing OSD ON. Verify that audio is being received.
T
Timothy CoxAug 28, 2025
Why does Lexicon DC-2 Recording Equipment center channel only play?
- T
  Tyler GatesAug 28, 2025
  If the center channel is the only sound you are getting from your Lexicon Recording Equipment, check if your HiFi VCR has dropped out of tracking. If so, readjust it. Also, check your VCR's Stereo/Mono/L-R switch. Make sure it is set to Stereo.
M
Miss Sandra Camacho DDSSep 1, 2025
How to fix muffled sound in L&R channels on Lexicon DC-2 Recording Equipment?
- S
  Stacy HarringtonSep 1, 2025
  If the sound in the L&R channels is muffled when using your Lexicon Recording Equipment, and you are not using a center channel, ensure that the CENTER is configured for NONE in the Setup Speaker Configuration menu.
A
Andrew MercadoSep 4, 2025
How to troubleshoot Lexicon Recording Equipment center channel sound muffled?
- J
  joshuafranklinSep 4, 2025
  If the center channel sound is muffled when using your Lexicon Recording Equipment, check the connection of the center channel amp. It may be incorrectly connected to the subwoofer jack on the DC-2 rear panel. If so, reconnect it to the Center Output jack.
A
Amanda WilsonSep 7, 2025
Why are there no Input Level Meters on my Lexicon DC-2 Recording Equipment?
- K
  Katelyn JacksonSep 7, 2025
  If you're not seeing input level meters on your Lexicon Recording Equipment, note that the meters will only appear when you are adjusting the Gain parameter of a selected, active input, or when the Status menu is displayed.

Lexicon DC-2 Specifications

General

Digital Inputs	Coaxial, Optical
THX Certified	Yes
THD	< 0.05%
Frequency Response	20 Hz - 20 kHz
Sampling Rate	48 kHz
MIDI	No
Decoding Formats	Dolby Digital, DTS
Analog Outputs	6 channels
Outputs	6-Channel
Dynamic Range	100 dB