Lexmark XM7163 - User Manual

Other manuals for Lexmark XM7163

Repair Manual510 pages

Brochure & Specs8 pages

Quick Start Guide29 pages

Questions and Answers

E
Erin CooperAug 20, 2025
What to do if my Lexmark All in One Printer says 'Cartridge very low'?
- A
  Angela WhiteheadAug 20, 2025
  To resolve the 'Cartridge very low' message on your Lexmark All in One Printer, you may need to replace the toner cartridge soon. If you want to clear the message and continue printing, touch Continue on the printer control panel.
V
vtownsendAug 22, 2025
What to do if Lexmark All in One Printer says 'Cartridge low'?
- B
  Bryce DonovanAug 22, 2025
  If your Lexmark All in One Printer displays 'Cartridge low', you might need to order a replacement toner cartridge. To clear the message and continue printing temporarily, touch Continue on the printer control panel.
A
adam40Aug 25, 2025
How to replace missing cartridge on Lexmark All in One Printer?
- N
  Nicholas WatkinsAug 25, 2025
  To clear the message on your Lexmark All in One Printer, install the missing cartridge.
M
Matthew WashingtonAug 27, 2025
What to do if Lexmark All in One Printer says 'Cartridge nearly low'?
- D
  dtranAug 27, 2025
  If your Lexmark All in One Printer displays 'Cartridge nearly low', touch Continue on the printer control panel to clear the message and continue printing.
J
Jeremy SnowAug 28, 2025
How to fix 'Check tray connection' on Lexmark All in One Printer?
- C
  Chelsea CraigAug 28, 2025
  To fix the 'Check tray [x] connection' error on your Lexmark All in One Printer, try the following: * Turn the printer off and then on again. * If the error persists: 1. Turn off the printer. 2. Unplug the power cord. 3. Remove and reattach the indicated tray. 4. Reconnect the power cord and turn the printer back on. * If the error continues, remove the tray and contact customer support. Alternatively, you can touch Continue on the printer control panel to clear the message and resume the job.
A
Alison NelsonAug 30, 2025
Why does my Lexmark All in One Printer say 'Close door or insert cartridge'?
- K
  Keith CurtisAug 30, 2025
  The 'Close door or insert cartridge' message on your Lexmark All in One Printer means that the toner cartridge is either missing or not correctly installed. Insert the cartridge properly, and ensure that all doors and covers are completely closed.
A
Aaron GarciaSep 1, 2025
How to fix 'Too many trays attached' error on Lexmark All in One Printer?
- M
  Martin RhodesSep 1, 2025
  To fix the 'Too many trays attached' error on your Lexmark All in One Printer: 1. Turn off the printer. 2. Unplug the power cord from the electrical outlet. 3. Remove the extra trays. 4. Connect the power cord to a properly grounded electrical outlet. 5. Turn the printer back on.
S
Stacy RojasSep 2, 2025
How do I fix 'Change paper source' on my Lexmark All in One Printer?
- C
  cbowersSep 2, 2025
  To resolve the 'Change [paper source] to [custom string] load [orientation]' message on your Lexmark All in One Printer, you can try the following: * Load the correct size and type of paper in the tray, then specify the paper size and type in the Paper menu on the control panel. Touch Finished changing paper. * Touch Use current [paper source] to use the available paper size and type in the tray. * Touch Reset active bin to reset the active bin for a linked set of bins. * You can also cancel the print job.
B
Brandi JonesSep 4, 2025
What to do if Lexmark All in One Printer shows 'Complex page' error?
- L
  lopezwilliamSep 4, 2025
  To address the 'Complex page' error on your Lexmark All in One Printer, you can: * Touch Continue on the printer control panel to ignore the message and continue printing. * Cancel the current print job. * Install additional printer memory.
R
Robert JohnstonSep 6, 2025
What to do if Lexmark All in One Printer shows 'Defective flash detected'?
- S
  Stephen HickmanSep 6, 2025
  To resolve the 'Defective flash detected' error on your Lexmark All in One Printer, you can: * Replace the defective flash memory card. * Touch Continue on the printer control panel to ignore the message and continue printing. * Cancel the current print job.