37
206-4342
Installer Menu (Cont.)
Installer Menu Items 000 through 041
Item Function Value Range Default Value Brief Description of Function
000 INSTALLER SEQ 0 – 3 0 Leave default set to 0.
001 POWER MANAGE 0 – 7 0
Selects the number of hours of inactivity allowed before the TV automatically
turns itself OFF. Set to 0 to disable Power Management.
002 AC ON 0 – 3, 16 – 19 0
Determines the status of the TV (ON, Instant ON enabled, etc.) when AC power
is applied. See detailed descriptions.
003 BAND/AFC 0 – 3 1 Selects the RF Tuning Band: 0=Broadcast, 1=Cable, 2=HRC, 3=IRC
004 STRT CHANNEL 0 – 127, 255 255
Channel tuned when the TV is turned ON. (Set to 255 to tune to channel
tuned before the TV was turned OFF.)
005 CHAN LOCK 0 / 1 0 If set to 1, cannot tune from current channel.
007 STRT VOLUME 0 – 63, 255 255
Volume level when the TV is turned ON. (Set to 255 to use volume level set
before the TV was turned OFF.)
008 MIN VOLUME 0 – 63 0 Sets the minimum allowable volume setting.
009 MAX VOLUME 0 – 63 63 Sets the maximum allowable volume setting.
010 MUTE DISABLE 0 / 1 0 Set to 1 to disable the Mute function.
011 KEY DEFEAT *
0 / 1 1
If set to 1, joystick button menu navigation functions on the display panel are
not available.
012 IR BANKS EN. 0 / 1 0 Set to 1 to enable TV to respond to bank discrete IR codes.
013 SCAN MODE 0 / 1 1
Set to 1 to allow Channel Up/Down key presses to turn ON TV. See
detailed descriptions.
014 STRT CH IN SM 0 / 1 0 Set to 1 to use the Start Channel for the Channel Map pivot point in Scan Mode.
015 SLEEP TIMER 0 / 1 1 Set to 1 to enable the Sleep Timer feature.
016 EN. TIMER 0 / 1 1 Set to 1 to enable On/Off timers.
017 ALARM 0 / 1 1 Set to 1 to enable the Alarm feature in the Function Menu.
020 FEATURE LEVEL
0 – 1, 16 – 24,
64 – 65
1 Determines an additional IR code scheme to which the TV will respond.
021 V-CHIP 0 / 1 1 Set to 1 to enable V-Chip (Parental Control) functions.
022 MAX BLK HRS 0 – 99 12
Determines the maximum number of Parental Control blocking hours that can
be set in the Function Menu.
023 CAPTION LOCK 0 / 1 0 Set to 1 to retain the caption setting selected before the TV was turned OFF.
025 FUNCTION PRE. 0 / 1 1
Set to 1 to allow Channel Preview/Banks Setup Menu access via the CH
PREVIEW key on the Installer Remote.
027 HOSPITAL MODE 0 – 162, 254 254
Set according to the speaker selection, the pillow speaker code/supply voltage,
and the hospital IR code. See detailed instructions.
028 CH. OVERIDE 0 / 1 1
If set to 0, users can only tune to channels that are included in the PTC
Channel Map. See detailed descriptions.
029 REMAP AUX INPS 0 / 1 0 Set to 1 to remap the PTC’s direct tune channels for Aux inputs from 13x to 9x.
030 ACK MASK 0 / 1 0 If set to 1, enables the ACK feature of MPI.
031 POLL RATE 20 – 169 94 Selects the poll rate for MPI.
032 TIMING PULSE 186 – 227 207 Sets the baud rate for MPI.
035 HDMI1 ENABLE 0 – 2 1
Set to 0 to disable HDMI 1. Set to 1 (DTV Mode) or 2 (PC Mode), as
applicable, to enable HDMI 1.
039 REAR AUX EN. 0 / 1 1 Set to 1 to enable the display panel AV input jack.
041 SIMPLINK EN 0 – 3 0 Determines the status of the SIMPLINK feature. See detailed descriptions.
* This item is applicable for 24/28LT572M TVs only.
To Next Page
Loading...
