EasyManua.ls Logo

Lightware HDMI-3D-OPT-TX210A - User Manual

Lightware HDMI-3D-OPT-TX210A
106 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
HDMI-3D-OPT-TX210A
HDMI-3D-OPT-TX210RAK
SW4-OPT-TX240RAK
User’s manual

Table of Contents

Other manuals for Lightware HDMI-3D-OPT-TX210A

Preview: Quick Start Guide
Quick Start Guide2 pages

Questions and Answers

  • R
    Ross SuttonAug 6, 2025
    Why is there no picture on the Lightware HDMI-3D-OPT-TX210A video output (receiver)?
    • A
      Adam ThomasAug 6, 2025
      If there's no picture on the video output, several factors could be at play. First, ensure all devices, including the extenders, are properly powered by checking and reconnecting them. Verify that all cable connections, including video and optical cables, are secure. Confirm that the correct port is selected in the Crosspoint settings. Check if the laser is disabled in the LINKOUT properties and ensure Autoselect settings are correct if enabled. Also, verify that the output is not muted and that the display can receive the video format by checking the emulated EDID. Finally, ensure HDCP is enabled on the input port if it was disabled.
  • C
    carpenterrobertAug 11, 2025
    What to do if connected serial device does not respond with Lightware HDMI-3D-OPT-TX210A Extender?
    • H
      Heather ReedAug 11, 2025
      If a connected serial device isn't responding, start by checking the cable connections to ensure they are properly fitted and wired correctly. Then, verify that the RS-232 settings on the transmitter, receiver, and connected serial device(s) match, paying close attention to Link and/or Local ports. Finally, confirm that the RS-232 mode (pass, control, or command injection) is correctly configured.
  • C
    Christine MeyersAug 15, 2025
    How to fix Lightware HDMI-3D-OPT-TX210A Extender when no LAN connection can be established?
    • G
      gordonlisaAug 15, 2025
      If you can't establish a LAN connection, it might be due to an incorrect IP address. Try using a dynamic IP address by enabling the DHCP option. If that doesn't work, restore the factory default settings (with fix IP). Also, check for IP address conflicts with other devices on the network.
  • K
    Kaitlyn RollinsAug 19, 2025
    Why is not the desired picture displayed on the Lightware Extender video output?
    • V
      Victoria CooperAug 19, 2025
      If the video output shows an undesired picture, it could be because the video output is statically set to a test pattern (no sync screen). Check the 'No sync screen' settings in the LINKOUT properties. Alternatively, if there's no picture on the video source, the video output might be set to a test pattern. In this case, check the video settings of the source.
  • J
    Jonathan FryAug 23, 2025
    Why does HDMI output signal contain no audio when using Lightware Extender?
    • J
      John PhillipsAug 23, 2025
      If your HDMI output signal contains no audio, it might be because the HDMI mode was set to DVI. Check the properties of the output port and set it to HDMI or Auto. It could also be that a DVI EDID is emulated. In that case, check the EDID and select an HDMI EDID to emulate.
  • R
    rpopeAug 28, 2025
    What to do if there is no audio present on Lightware Extender output?
    • M
      Megan RodriguezAug 28, 2025
      If there's no audio on the output, first check the crosspoint settings of the audio layer to ensure the correct audio port is switched to the output. Then, verify that the source audio volume is not low or muted by checking the audio settings of the source. Also, confirm that the output port is not muted by checking its properties. Finally, ensure that the analog audio volume is not set too low in the Analog audio input port settings.
  • M
    Mary MoralesSep 1, 2025
    What to do if Lightware HDMI-3D-OPT-TX210A error messages received always?
    • T
      tammywhiteSep 1, 2025
      If you're constantly receiving error messages, it may be due to a mismatched protocol setting. Verify the port protocol settings (LW2 / LW3) and ensure you're using the correct protocol commands.

Summary

Users Manual

HDMI-3 D-OPT-TX200 Series

Manual title for the HDMI-3D-OPT-TX200 series of extenders.

HDMI-3 D-OPT-TX210 A

Specific model covered in the manual.

HDMI-3 D-OPT-TX210 RAK

Specific model covered in the manual.

SW4-OPT-TX240 RAK

Specific model covered in the manual.

SAFETY INSTRUCTIONS

Caution: Laser product

Warning regarding potential hazards associated with laser components.

Limited Warranty Statement

Warranty Terms and Conditions

1. Introduction

1.2. Description

Overview of the HDMI-3D-OPT-TX200 series extender's capabilities and features.

1.5. Features

2. Installation and controls

2.2. Connecting steps

Provides a step-by-step guide for connecting the transmitter to sources and displays.

2.7. Electrical connections

3. Technologies

3.3. Advanced EDID Management

3.4. HDCP Management

Information on High-bandwidth Digital Content Protection (HDCP) features and troubleshooting.

4. Optical extender concept

4.2. Video interface

Explains how video crosspoint settings are controlled and port selection methods.

4.3. Controlling features

5. Operation

5.1. Front panel operation - Special functions

5.2. Software control modes

Overview of available software control methods: LDC, LW2, and LW3 protocols.

6. Software control - Using Lightware Device Controller

6.1. Install and upgrade

6.2. Establishing the connection

Steps to connect the device to a computer using USB, RS-232, or Ethernet.

6.3. Crosspoint menu

Overview of the Crosspoint menu interface within LDC for managing signal routing.

6.4. Port properties and settings

Details on renaming ports, muting, locking, autoselect, and frame detection.

6.5. EDID menu

Interface for managing EDID data, including emulation, learning, exporting, and editing.

6.6. Control menu

6.7. Event Manager

Feature for creating automated actions based on specific conditions.

6.8. Settings menu

6.9. Configuration cloning (Backup tab)

Method for backing up and restoring device configurations to save time.

6.10. Advanced view

Interface for running and setting commands not available in the GUI.

7. LW2 programmers reference

7.1. LW2 protocol description

7.2. General LW2 commands

7.3. Port and crosspoint settings

Commands for switching, muting, locking, and managing autoselect for ports.

7.4. Network configuration

7.6. LW2 commands - Quick summary

8. LW3 programmers reference

8.1. Overview

8.2. The tree structure of the transmitter

8.3. LW3 commands

Detailed explanation and examples of GET, SET, CALL, MAN commands.

8.5. Video port and crosspoint settings

Commands for querying and changing video crosspoint, autoselect, and priority settings.

8.6. Audio port settings

8.7. RS-232 port configuration

8.8. Network configuration

8.10. EDID management

Commands for managing EDID emulation, copying, deleting, and resetting.

8.11. LW3 commands - Quick summary

9. Firmware upgrade

9.3. Install and upgrade

9.4. Detailed instructions

9.5. Keeping the configuration settings after firmware upgrade

10. Troubleshooting

Troubleshooting Common Issues

Guides for diagnosing and resolving common issues with signal transport and display.

Lightware HDMI-3D-OPT-TX210A Specifications

General IconGeneral
CategoryExtender
Signal TypeHDMI
Input ConnectorHDMI
Input Ports1
Output Ports1
Max Bandwidth18 Gbps
Connector TypeLC Duplex
3D SupportYes
Power Supply5V DC
TypeFiber Optic
Output ConnectorHDMI
Supported ResolutionsUp to 4K@60Hz
Maximum Distance10 km
Transmission Distance100m
HDCP SupportHDCP 2.2
Operating Temperature0°C to +50°C (32°F to 122°F)
Storage Temperature-20°C to +70°C (-4°F to +158°F)
Power Consumption5W

Related product manuals