EasyManua.ls Logo

Lightware HDMI-3D-OPT-TX210RAK - User Manual

Lightware HDMI-3D-OPT-TX210RAK
106 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
HDMI-3D-OPT-TX210A
HDMI-3D-OPT-TX210RAK
SW4-OPT-TX240RAK
User’s manual

Table of Contents

Other manuals for Lightware HDMI-3D-OPT-TX210RAK

Preview: Quick Start Guide
Quick Start Guide2 pages

Questions and Answers

  • L
    Levi FernandezAug 6, 2025
    Why is there no picture on the Lightware Extender video output (receiver)?
    • D
      Daryl SmithAug 6, 2025
      If there's no picture on the video output, several factors could be at play. First, ensure all devices, including the extenders, are properly powered by checking and reconnecting them. Verify that all cable connections, including video and optical cables, are secure. Confirm that the correct port is selected in the Crosspoint settings. Check if the laser is disabled in the LINKOUT properties and ensure Autoselect settings are correct if enabled. Also, verify that the output is not muted and that the display can receive the video format by checking the emulated EDID. Finally, ensure HDCP is enabled on the input port if it was disabled.
  • P
    Paul WatsonAug 10, 2025
    What to do if connected serial device does not respond with Lightware Extender?
    • G
      Glenda MckenzieAug 10, 2025
      If a connected serial device isn't responding, start by checking the cable connections to ensure they are properly fitted and wired correctly. Then, verify that the RS-232 settings on the transmitter, receiver, and connected serial device(s) match, paying close attention to Link and/or Local ports. Finally, confirm that the RS-232 mode (pass, control, or command injection) is correctly configured.
  • B
    bullocksamanthaAug 15, 2025
    How to fix Lightware Extender when no LAN connection can be established?
    • T
      Todd ColemanAug 15, 2025
      If you can't establish a LAN connection, it might be due to an incorrect IP address. Try using a dynamic IP address by enabling the DHCP option. If that doesn't work, restore the factory default settings (with fix IP). Also, check for IP address conflicts with other devices on the network.
  • M
    Monica FieldsAug 19, 2025
    Why is not the desired picture displayed on the Lightware Extender video output?
    • K
      Kylie HuangAug 19, 2025
      If the video output shows an undesired picture, it could be because the video output is statically set to a test pattern (no sync screen). Check the 'No sync screen' settings in the LINKOUT properties. Alternatively, if there's no picture on the video source, the video output might be set to a test pattern. In this case, check the video settings of the source.
  • M
    moorebriannaAug 25, 2025
    Why does HDMI output signal contain no audio when using Lightware HDMI-3D-OPT-TX210RAK Extender?
    • D
      David GilbertAug 25, 2025
      If your HDMI output signal contains no audio, it might be because the HDMI mode was set to DVI. Check the properties of the output port and set it to HDMI or Auto. It could also be that a DVI EDID is emulated. In that case, check the EDID and select an HDMI EDID to emulate.
  • R
    rebeccamcleanAug 28, 2025
    What to do if there is no audio present on Lightware Extender output?
    • A
      Alice AdkinsAug 28, 2025
      If there's no audio on the output, first check the crosspoint settings of the audio layer to ensure the correct audio port is switched to the output. Then, verify that the source audio volume is not low or muted by checking the audio settings of the source. Also, confirm that the output port is not muted by checking its properties. Finally, ensure that the analog audio volume is not set too low in the Analog audio input port settings.
  • J
    Jermaine BoydAug 31, 2025
    What to do if Lightware HDMI-3D-OPT-TX210RAK error messages received always?
    • K
      Karla RamirezSep 1, 2025
      If you're constantly receiving error messages, it may be due to a mismatched protocol setting. Verify the port protocol settings (LW2 / LW3) and ensure you're using the correct protocol commands.

Summary

Safety Instructions

Limited Warranty Statement

2. Installation and Controls

2.1. Mounting Options

Details on how to physically install the transmitter using mounting kits.

2.2. Connecting Steps

Step-by-step guide for connecting sources, displays, and power.

Front Panel Overview

Rear View Overview

2.7. Electrical Connections

2.7.1. DC 5 V Connection

Explains how to connect the DC power adapter, including locking mechanism.

Connector Details

3. Technologies

HDCP Management

Explains HDCP handling, protected content, and real-life examples.

4.3. Device Control Interfaces

4.3.1. Serial Interface Modes

4.3.2. USB Control Interface

4.4. Further Built-in Features

EDID Management

Transmitter Configuration Cloning

Method for backing up and restoring device configuration settings.

5. Operation

Front Panel Special Functions

Operations like control lock, reset, DHCP enable, and bootload mode.

6. Software Control: Lightware Device Controller (LDC)

LDC Installation and Upgrade

Establishing LDC Connection

LDC Crosspoint Menu

Overview of the Crosspoint menu for managing signal routing.

LDC Port Properties and Settings

LDC Advanced Port Settings

LDC EDID Menu

LDC Control Menu

LDC Event Manager

Setting up automated actions based on events and conditions.

LDC Settings and Configuration Cloning

LDC Advanced View

7. LW2 Programmers Reference

LW2 Port and Crosspoint Control

LW2 Network Configuration

LW2 GPIO Settings

8. LW3 Programmers Reference

LW3 Commands: Get, Set, and Invoke

LW3 Video Port and Crosspoint Control

LW3 commands for video switching, autoselect, and priority settings.

LW3 Audio, RS-232, and Network Configuration

LW3 commands for audio settings, RS-232 ports, and network management.

LW3 GPIO and EDID Management

LW3 commands for GPIO settings and EDID management operations.

9. Firmware Upgrade

Firmware Package and Installation

Detailed Upgrade Procedure

Step-by-step guide for connecting and performing firmware upgrades.

Keeping Settings After Upgrade

Options to retain configuration or perform a factory reset post-upgrade.

10. Troubleshooting

Video and Display Issues

Troubleshooting steps for no picture or incorrect picture display.

Audio, Serial, and Network Issues

Diagnosing problems with audio, serial communication, and network connectivity.

Front Panel and Error Message Issues

Troubleshooting front panel operation and persistent error messages.

Lightware HDMI-3D-OPT-TX210RAK Specifications

General IconGeneral
ModelHDMI-3D-OPT-TX210RAK
Input InterfaceHDMI
3D SupportYes
Power Supply5V DC
Product CategoryExtender
Video ResolutionsUp to 4K
Fiber TypeSingle-mode
Supported 3D FormatsFrame packing, Side-by-side, Top-and-bottom
Audio FormatsDolby Digital, DTS, LPCM
Operating Temperature0°C - +50°C
Storage Temperature-20°C to +70°C
ConnectorsHDMI

Related product manuals