Lightware VINX-120-HDMI-ENC

Other manuals for Lightware VINX-120-HDMI-ENC

Questions and Answers:

Sarah LewisAug 11, 2025

What to do if the video stream cannot be changed by the keyboard shortcut on Lightware VINX-120-HDMI-ENC Extender?

M
Michael OliverAug 11, 2025
If you're unable to change the video stream using keyboard shortcuts, here are some possible solutions: * If your keyboard is connected to a USB 2.0 port, connect it to the USB 1.1 port instead. * Ensure that the shortcut is assigned correctly in the settings. If not, set the shortcut(s) again. * Verify that the keyboard is connected to the correct Decoder. Connect it to the desired Decoder. * Check if another Decoder is selected for USB transmission. Look at the LEDs or the USB settings in the built-in web page.

rodney70Aug 18, 2025

What to do if there is no video on the screen using Lightware VINX-120-HDMI-ENC Extender?

K
Kimberly BuckAug 18, 2025
If there's no video on the screen, here are a few things to check: * First, ensure that there is a video signal coming in and that all cable connections are secure. * Next, verify that the Video Stream IDs are correctly assigned in the extender settings. * If HDCP is disabled (EDID information cannot be read), enable HDCP on the input of the Encoder. In some cases, the source device might not be able to read the EDID from the Encoder. * Also, confirm you are not sending HDCP-encrypted content to a non-HDCP capable device, if so, replace it with a HDCP-capable one.

patriciasantosAug 26, 2025

Why I cannot connect to a Lightware Extender?

T
Tammy NelsonAug 26, 2025
If you're having trouble connecting to a Lightware Extender, consider these potential causes: * The extenders might not have received an IP address. If this is the case, reboot the VINX devices, as the Ethernet switch might need more time to be ready than the extenders. * The extender might not be properly connected. Check the LEDs and cable connections. * The extenders and your PC may not be on the same subnet. Ensure that all devices are located in the same subnet.

Bruce SimpsonSep 2, 2025

How to connect the Encoder and the computer over USB with Lightware Extender?

N
Nicole ThomasSep 2, 2025
Connect the supplied USB cable between the computer and the Encoder.

Lightware VINX-120-HDMI-ENC Specifications

General

Category	Extender
Model	VINX-120-HDMI-ENC
Input Ports	1 x HDMI
Video Resolutions	Up to 4K@60Hz
Power Supply	12V DC
Weight	0.3 kg
Transmission Distance	Up to 100m over CATx
Audio	Dolby Digital, DTS
Control	RS-232
Other Features	EDID management
Latency	Less than 1ms
Ethernet Port	1x RJ45
Operating Temperature	0°C to 40°C

Lightware VINX-120-HDMI-ENC - User Manual

Table of Contents

Other manuals for Lightware VINX-120-HDMI-ENC

Questions and Answers:

Lightware VINX-120-HDMI-ENC Specifications

Summary

Important Safety Instructions

General Safety Precautions

Common Safety Symbols and WEEE Information

Safety Symbol Reference

Introduction to VINX Extenders

Product Overview: Description and Features

VINX Product Details

Basic and AP-Series Model Descriptions

VINX Extender Key Features

Core Device Features Overview

Product Overview

Installation Guide

Mounting Options Overview

Rackmount Cage Installation

Electrical Connections and Connecting Steps

VINX Mounting Options

VESA100, Under-Desk, and Rack Shelf Mounting

Powered Rackmount Cage Installation

Cage Features and Assembly Steps

Electrical Connections and Ports

Network, Dante, SFP, and Analog Audio Ports

Microphone Input and RS-232 Port Details

Connecting VINX Extenders

Network Preparation and Multicast Connection

VINX Connection Modes

Unicast Connection and Installation Checkpoints

Software Control Options

Control Methods Overview

Using Lightware Device Controller (LDC)

Connecting via Built-in Web Page

Main Settings: Encoder and Decoder

Crosspoint, Multiviewer, and EDID Management

Advanced Settings Configuration

Software Control Modes Explained

Built-in Web vs. LDC Functionality Comparison

Connecting with Lightware Device Controller (LDC)

LDC Installation, Running, and Upgrading

Connecting via Built-in Web Page

Finding Device IP Address

Default IP Address Configuration

Encoder Main Settings: General

Mode, Stream ID, and Grouping Settings

Decoder Assignment and Device Labeling

Encoder: Video Status and Settings

Video Signal, HDCP, Source, and Bandwidth Settings

Encoder: Audio Settings

General Audio Configuration

Decoder Main Settings: General

Mode, Stream ID, and Decoder Assignment

Decoder: Video Status and Settings

Video Status and Scaling Configuration

Decoder: No Signal Screen and Scaling

No Signal Screen and Scaling Options

Decoder: Audio Settings

Audio Sink Selection and Volume Control

Crosspoint Menu Operation

Crosspoint Interface and Frame Detector

EDID Operations

EDID Management: Change, Learn, Export, Import, Delete

Advanced Settings: Common Configurations

Network, Firmware, RS-232, and USB Settings

Device Restart and Factory Defaults

Advanced Settings: Decoder Specific

OSD, Keyboard Shortcuts, and Stream ID List

Scaler Settings for Decoders

LW3 Terminal Interface

LW3 Terminal Window and Controls

Video Wall Setup Configuration

Creating and Identifying Video Walls

Video Wall Gap and Bezel Settings

Gap and Bezel Parameter Configuration

Modifying and Deleting Video Walls

Video Wall Modification and Deletion Procedures

Programmers Reference Guide