10. Appendix
10.9. Firmware Release Notes
v2.0.2b4
Release date: 2021-02-01
New feature:
▪ From this version on, black screen or the VINX screen can be
selected to display when there is no video signal in the decoder.
v2.0.1b3
▪ Fixed a bug that caused popping sound on analog audio output
when changing streams
Known issue:
▪ On a VINX-110AP-HDMI-DEC, when both USB 2.0 ports in used,
the analog audio signal on the output might be jammed during
stream change
v2.0.0b27
Release date: 2020-01-17
New feature:
▪ Factory defaults button added to Advanced Setup page.
▪
HDMI-ENC-DNT encoder.
▪ From this version on, the device can be set to use static IP
address, use dynamic IP address either with or without falling
back to AutoIP, or continue with dynamic IP address query even
after AutoIP was set.
▪ From this version on, the HPD signal on the HDMI input of an
encoder can be toggled.
▪ Improved switching time considerably. (Switching time is the
time elapsed between switching to another source and providing
a stable output on the output HDMI port.)
▪
when the sender closed the TCP connection before receiving an
answer for the request from the VINX device.
v1.4.0b7
New feature:
▪ Added support for VINX-210AP-HDMI-ENC, VINX-120AP-HDMI-
ENC, and VINX-110AP-HDMI-DEC.
▪ From this version on, the exact product name is presented to the
▪ From this version on, both the encoder and the decoder can be
set whether or not to use jumbo frames. Note, that this setting is
encoder shall be set to the same setting.
▪ Fixed a bug that might have resulted in the Advanced Settings
page to be rendered incorrectly at some resolutions.
▪ On a VINX-120-HDMI-ENC device, The EDID is not read from the
sink connected to the local output of the encoder. Thus, it cannot
be used as a dynamic EDID.
▪ Some parameters of the EDID emulated on the HDMI input of
VINX-210AP-HDMI-ENC and VINX-120AP-HDMI-ENC (other than
▪ VINX-210AP-HDMI-ENC might indicate wrong resolution for
▪ On a VINX-110AP-HDMI-DEC, compressed audio might be output
for a brief period of time which results in digital noise on the output.
Known issue:
▪ Pressing the front panel key (COMP MODE or USB CONNECT)
for less than ten seconds might reset the device to its factory
settings.
▪ On a VINX-120-HDMI-ENC device, The EDID is not read from the
sink connected to the local output of the encoder. Thus, it cannot
be used as a dynamic EDID.
▪ Some parameters of the EDID emulated on the HDMI input of
VINX-210AP-HDMI-ENC and VINX-120AP-HDMI-ENC (other than
▪ VINX-210AP-HDMI-ENC might indicate wrong resolution for
▪ On a VINX-110AP-HDMI-DEC, compressed audio might be output
for a brief period of time which results in digital noise on the
output.
v1.3.0b5
Release date: 2018-12-18
New feature:
▪ Added controls for setting the RS-232 mode to Pass-through or
Command injection.
▪ Added a Crosspoint tab to the graphical user interface. In the
crosspoint tab it is possible to route any input to any output as
long as the number of encoders and decoders in the subnet does
▪
▪ Fixed a bug that caused the Output scaling radio button group to
work hectically when the Output standard is set to DVI.
v1.2.1b1
▪ Fixed a bug that resulted in wrong output format for scaling set
v1.2.0b9
Release date: 2018-10-18
New feature:
▪ From this version on, the video mode related settings (Video
quality as referred to in earlier versions) have been given a more
descriptive and self explaining name.
▪ The Connect button in the Main Settings page has been renamed
to Open Device.
▪
Device Manager.
▪ From this version on, the graphical user interface displays a
preview image of the encoder input.
▪ Improved response time of the devices. As a result, changes
interface.
▪ The list of available output formats has been consolidated and a
few output formats have been added.
▪ From this version on, the name of the device appears on the tab
To Next Page
Loading...
