EasyManua.ls Logo

Lightware HDMI-TPS-TX226 - User Manual

Lightware HDMI-TPS-TX226
159 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
HDMI-TPS-TX210, HDMI-TPS-TX220
HDMI-TPS-TX226
DVI-HDCP-TPS-TX210, DVI-HDCP-TPS-TX220
DP-TPS-TX210, DP-TPS-TX220
SW4-TPS-TX240, SW4-TPS-TX240-Plus
User’s Manual
HDBaseT
TM
Multimedia Extender
v3.2

Table of Contents

Questions and Answers

  • S
    Sophia OlsonAug 19, 2025
    Why is there no picture on my Lightware HDMI-TPS-TX226 Extender's video output?
    • I
      isanchezAug 19, 2025
      Several factors can cause a missing picture on the video output: * The devices might not be powered correctly. Ensure all extenders and connected devices are properly powered, and try unplugging and reconnecting them. * There may be a cable connection issue. Verify that all video and TPS cables are securely connected. * There could be a problem with the TPS mode. Check the current TPS mode and the selected modes on the extenders. * The input or output port might be muted. Verify the mute state of both input and output ports. * The display may not support the current video format. Check the emulated EDID and try selecting a different one, such as emulating the display's EDID on the input port. * HDCP might be disabled. Enable HDCP on both the input and output ports.
  • A
    Andrew CostaAug 21, 2025
    What to do if there is no audio on the Lightware Extender output?
    • J
      John ColeAug 21, 2025
      If there's no audio on the output, consider these potential causes: * The source audio volume may be too low or muted. Check the audio settings of the source. * The audio input port could be muted. Check the audio input port properties. * The audio output port might be muted. Verify the output port properties.
  • S
    scomptonAug 23, 2025
    What to do if the Lightware HDMI-TPS-TX226 Extender displays the wrong picture?
    • D
      Donald HenryAug 23, 2025
      If the video output displays an incorrect picture, it might be due to: * The video output being set to a static test pattern (no sync screen). Check the test pattern settings in the properties of the output ports. * The video output being set to a test pattern (no sync screen) because there is no picture on the video source. Check the video settings of the source.
  • E
    evelynmackAug 26, 2025
    Why can't I establish a LAN connection with my Lightware Extender?
    • R
      rfosterAug 26, 2025
      If you're unable to establish a LAN connection, it could be due to: * An incorrect static IP address. Try using a dynamic IP address by enabling the DHCP option. * If that doesn't work, restore the factory default settings (with a fixed IP address).
  • A
    Anne SmithAug 28, 2025
    Why does my Lightware HDMI-TPS-TX226 Extender HDMI output signal have no audio?
    • S
      sara23Aug 28, 2025
      If the HDMI output signal lacks audio, it could be because: * The HDMI mode was set to DVI. Check the output port properties and set the signal type to HDMI or Auto. * A DVI EDID is being emulated. Check the EDID settings and select an HDMI EDID to emulate.
  • M
    Mark VazquezAug 30, 2025
    What to do if my Lightware HDMI-TPS-TX226 connected serial device does not respond?
    • J
      jessicapinedaAug 30, 2025
      If a connected serial device isn't responding, consider the following: * There may be a cable connection problem. Check the connectors to ensure a secure fit and verify the wiring of the plugs. * The RS-232 settings might be different. Check the port settings of the transmitter and the connected serial device(s). * The RS-232 mode might be incorrect. Check the RS-232 mode settings (control, command injection, or disconnected).
  • R
    ronaldsilvaSep 1, 2025
    What to do if my Lightware HDMI-TPS-TX226 receives error messages continuously?
    • M
      Molly JamesSep 1, 2025
      If you're receiving continuous error messages, it might be due to a different protocol being set. Check the port protocol settings (LW2 / LW3) and use the proper protocol commands.
  • J
    John MaySep 3, 2025
    How to make Lightware HDMI-TPS-TX226 Extender read out the EDID again?
    • L
      Lisa JohnsonSep 3, 2025
      You need to restart your source to make it read out the EDID again.
  • I
    isanchezSep 7, 2025
    What to do if there is no audio output from Lightware Transmitter?
    • J
      Justin WilsonSep 8, 2025
      If there's no audio present on the output of your Lightware Transmitter, consider the following: * **Crosspoint Settings:** Verify the audio layer crosspoint settings to ensure the correct audio port is switched to the output. * **Source Volume:** Check the audio settings of the source device to ensure the volume is not low or muted. * **Output Port Mute:** Review the output port properties to confirm it is not muted. * **Analog Audio Volume:** If using analog audio, check the Analog audio input port settings and ensure the volume is not set too low.
  • C
    Charles EstradaSep 10, 2025
    Why does my Lightware Transmitter HDMI output have no audio?
    • L
      lgoodwinSep 10, 2025
      If your Lightware Transmitter's HDMI output signal contains no audio, check the following: * **HDMI Mode:** Verify the properties of the output port and ensure it is set to HDMI or Auto, not DVI. * **EDID Emulation:** Check the EDID settings and select an HDMI EDID to emulate, rather than a DVI EDID.

Lightware HDMI-TPS-TX226 Specifications

General IconGeneral
CategoryExtender
InputHDMI
OutputHDMI
HDCPHDCP 1.4
Power Supply5V DC
Transmission DistanceUp to 100 m
Other FeaturesPoE support
Input Ports1x HDMI
Operating Temperature0 to 40 °C
Storage Temperature-20°C
Humidity90% non-condensing

Related product manuals