Lightware UMX-TPS-TX130

Other manuals for Lightware UMX-TPS-TX130

Quick Start Guide2 pages

Questions and Answers

C
Christopher WilliamsAug 18, 2025
How to fix no picture on Lightware Extender video output?
- S
  Stephanie RichardsonAug 18, 2025
  If you're not getting any picture on the video output of your Lightware Extender, there are several potential causes: * **Power Issues:** Ensure all devices, including the extenders themselves, are properly powered. Try unplugging and reconnecting them. * **Cable Problems:** Make sure all cables, including video and TPS cables, are securely connected. * **TPS Mode:** Verify that the TPS mode and the selected modes of the extenders are correctly configured. * **Muted Ports:** Check if the input or output port is muted. * **Display Compatibility:** Ensure the display is capable of receiving the video format. Try emulating the display’s EDID on the input port. * **HDCP:** Enable HDCP on both the input and output ports.
J
Jennifer MitchellAug 20, 2025
Why does Lightware Extender HDMI output have no audio?
- A
  Amanda HunterAug 20, 2025
  If the HDMI output signal from your Lightware Extender contains no audio, there are a couple of things to check: * **HDMI Mode:** Verify the output port properties and ensure the signal type is set to HDMI or Auto, not DVI. * **EDID Emulation:** Check the EDID settings and select an HDMI EDID to emulate instead of a DVI EDID.
T
Thomas WilsonAug 23, 2025
What to do if Lightware Extender displays the wrong picture?
- S
  Sharon HaysAug 23, 2025
  If the picture displayed on the video output of your Lightware Extender isn't what you expect, here's what to investigate: * **Test Pattern Settings:** Check the input ports properties to ensure the video input is not set to a static test pattern (no sync screen). * **Crosspoint Settings:** Verify that the video source isn't set to Testpattern input (I6). * **Source Video Settings:** Confirm that the video output isn't set to a test pattern because there's no picture on the video source. Check video settings of the source.
E
ethanjonesAug 26, 2025
How to troubleshoot no audio on Lightware Extender output?
- R
  Richard HenryAug 26, 2025
  If you're not getting any audio on the output of your Lightware Extender, consider the following: * **Source Audio:** Check the audio settings of the source to ensure the volume isn't too low or muted. * **Input Port:** Verify the audio input port properties to make sure it's not muted. * **Output Port:** Check the output port properties to confirm it's not muted.
R
Richard WrightAug 27, 2025
Why can't I establish a LAN connection with my Lightware Extender?
- D
  Daniel AustinAug 27, 2025
  If you're unable to establish a LAN connection with your Lightware Extender, try the following: * **IP Address:** If using a static IP, ensure the IP address is correct. Consider using a dynamic IP address by enabling the DHCP option. * **Factory Reset:** Restore the factory default settings (with fix IP). * **IP Conflict:** Check for IP address conflicts with other devices on the network.
L
Lisa BrownAug 30, 2025
How to fix a Lightware Extender when connected serial device does not respond?
- C
  christophersantiagoAug 30, 2025
  If a connected serial device isn't responding when connected to your Lightware Extender, check these things: * **Cable Connections:** Ensure the connectors fit well and check the wiring of the plugs. * **RS-232 Settings:** Verify that the port settings of the transmitter and the connected serial device(s) match. * **RS-232 Mode:** Confirm that the RS-232 mode settings (control, command injection, or disconnected) are correct.
H
Heather DavisSep 1, 2025
How to stop continuous error messages on Lightware Extender?
- R
  Robert PooleSep 1, 2025
  If you are continuously receiving error messages with your Lightware Extender, check the port protocol settings (LW2 / LW3) and use the proper protocol commands. It may be that a different protocol is set.
S
Sara JohnsonSep 3, 2025
Why doesn't changing EDID on Lightware Extender change resolution?
- J
  Jeffrey BeckSep 3, 2025
  If you've changed the EDID on an input port of your Lightware device to get a different resolution and nothing happens, you need to restart your source to make it read out the EDID again.
S
Stephanie GarrettSep 8, 2025
What to do if there is no audio output from Lightware UMX-TPS-TX130?
- D
  donnadouglasSep 8, 2025
  If there's no audio present on the output of your Lightware Transmitter, consider the following: * **Crosspoint Settings:** Verify the audio layer crosspoint settings to ensure the correct audio port is switched to the output. * **Source Volume:** Check the audio settings of the source device to ensure the volume is not low or muted. * **Output Port Mute:** Review the output port properties to confirm it is not muted. * **Analog Audio Volume:** If using analog audio, check the Analog audio input port settings and ensure the volume is not set too low.
J
joelpenaSep 12, 2025
Why does my Lightware UMX-TPS-TX130 Transmitter HDMI output have no audio?
- G
  Gloria DorseySep 12, 2025
  If your Lightware Transmitter's HDMI output signal contains no audio, check the following: * **HDMI Mode:** Verify the properties of the output port and ensure it is set to HDMI or Auto, not DVI. * **EDID Emulation:** Check the EDID settings and select an HDMI EDID to emulate, rather than a DVI EDID.

Summary

Important Safety Instructions

Common Safety Symbols

Explains standard safety symbols used in the manual for electrical and operational safety.

3. Installation

3.1. Mounting Options - Standalone Transmitters

Covers methods for mounting standalone transmitters, including rack shelves and under-desk kits.

3.3. Mounting Options - Wall Plates

Details how to mount transmitters into industrial standard switch/outlet boxes.

3.4. Electrical Connections

Explains the types of electrical connections supported, including DC power and specific port connectors.

3.5. Connecting Steps

Provides step-by-step instructions for connecting sources and receivers to the devices.

3.6. Powering Options

Outlines various methods for powering the devices, including local PSU and Power over Ethernet (PoE).

5. SOFTWARE CONTROL - LIGHTWARE DEVICE CONTROLLER

5.1. Install and Update

Guides users through installing and updating the Lightware Device Controller (LDC) software.

5.3. Connecting to a Device (Device Discovery Window)

Explains how to connect to devices using Ethernet, Serial, or USB interfaces via the discovery window.

5.4. Crosspoint Menu

5.7. Diagnostic Tools

Explains tools for diagnosing cable issues and system health, including Cable Diagnostics and Test Pattern.

5.10. Event Manager

Explains how to create and manage events based on conditions and actions for automated control.

5.12. Configuration Cloning (Backup Tab)

Guides on backing up and restoring device configurations for cloning settings across multiple devices.

7. LW3 PROGRAMMERS’ REFERENCE

7.5. Cleartext Login Protection

7.9. Event Manager Basics

Explains how to arrange events by defining conditions, actions, and linking them.

8. FIRMWARE UPDATE

8.3. Running the Software

8.4. Updating via GUI

Provides a step-by-step guide for performing firmware updates using the graphical user interface.

8.7. If the Update is not successful

9. TROUBLESHOOTING

9.1. Use Cases

Provides a table of common symptoms, root causes, actions, and referneces for troubleshooting.

Lightware UMX-TPS-TX130 Specifications

General

Product Category	Transmitter
Output Ports	1 x HDBaseT
HDBaseT	Yes
USB	Yes
EDID Management	Yes
Input Ports	1 x HDMI, 1 x USB
Video Resolution	Up to 4K@60Hz
HDCP	HDCP 2.2
Operating Temperature	0°C to +40°C
Storage Temperature	-20 to 70 °C
Humidity	10% to 90% (non-condensing)