Linksys LAPAC2600 User Manual

SSID Settings
SSID Name
Enter the desired SSID Name. Each SSID must have a
unique name. The name includes 1 to 32 characters.
Broadcast
Enable or disable the broadcast of the SSID.
When the access point does not broadcast its SSID, the
network name is not shown in the list of available networks
on a client station. Instead, you must enter the exact
network name manually into the wireless connection utility
on the client so that it can connect.
Isolation
Enable or disable isolation among clients of the SSID. If
enabled, wireless clients cannot communicate with others
in the same SSID.
It is disabled by default.
802.11k
Enable or disable 802.11k of the SSID.
The 802.11k protocol provides mechanisms for APs and
clients to measure the available radio resources
dynamically. In an 802.11k enabled network, APs and
clients can send neighbor reports, beacon reports, and link
measurement reports to each other. This allows the APs
and clients to take appropriate connection actions for next
hop if client has weak connection to current AP.
VLAN ID
Enter the VLAN ID of the SSID.
Used to tag packets which are received from the wireless
clients of the SSID and sent from Ethernet or WDS
interfaces.
Applicable only when VLAN function is enabled. VLAN
function can be configured in Configuration -> LAN ->
Network Setup screen.
Max Clients
Enter the number of clients that can connect to the SSID.
The range is from 0 to 32 and 0 means no limit.
32

Linksys LAPAC2600 Specifications

General

2.4 GHz	Yes
Frequency band	2.412 - 2.462, 5.18 - 5.24, 5.745 - 5.825 GHz
Channels quantity	13 channels
Number of VLAN IDs	17
Fit AP mode features	Wireless distribution system (WDS)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11k, IEEE 802.11n, IEEE 802.11r, IEEE 802.1x, IEEE 802.3at
Receiver sensitivity	802.11b 11Mbps: -85dBm 802.11a/g 54Mbps: -73dBm 802.11n HT20 MCS7: -67dBm 802.11n HT40 MCS7: -65dBm 802.11n HT40 MCS7: -65dBm
Virtual LAN features	SSID-based VLAN assignment
Wi-Fi data rate (max)	1733 Mbit/s
Ethernet LAN data rates	1000 Mbit/s
Maximum data transfer rate	2533 Mbit/s
Output current	2.5 A
Output voltage	12 V
Power consumption (max)	25 W
Internal	No
Placement	Ceiling, Wall
Certification	FCC: 47 CFR FCC Part 15, Subpart B, Class B; 47 CFR FCC Part 15, Subpart C; 47 CFR FCC Part 15, Subpart E CE: EN55022, Class B; EN61000-3-2; EN61000-3-3; 55024; EN 301 489-1 / EN 301 489-17, Class B; EN 300 328; EN 301 893; EN 62311; EN 50385
Product color	White
LED indicators	System
Cable lock slot type	Kensington
USB 2.0 ports quantity	0
Ethernet LAN (RJ-45) ports	2
Antenna features	Integrated antenna
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	10 - 90 %
Operating relative humidity (H-H)	10 - 85 %
Security algorithms	802.1x RADIUS, HTTPS, SNMP, WPA, WPA2
Number of SSID supported	16
Service Set Identifier (SSID) features	Hidden SSID
Cables included	LAN (RJ-45)

Weight and Dimensions

Depth	243 mm
Width	237 mm
Height	43.69 mm
Weight	848 g