How to fix Lippert Components Control Systems when it will not turn on?
If the Lippert Components Control System won't turn on and the indicator light is off, make sure the coach ignition is in the RUN position and the parking brake is set. If the controls have been on for more than four minutes, they may have timed out; try turning the ignition OFF and then back ON.
What to do if Lippert Components LCI Level-Up Control Systems panel turns off when jack button is pushed?
If your Lippert Components Control Systems panel turns on but shuts off when you push the jack button or displays 'Low Voltage,' the battery voltage may be low. Try starting the coach to charge the battery.
Why Lippert Components LCI Level-Up Control Systems jacks will not extend?
If the jacks on your Lippert Components Control Systems won't extend to the ground but the pump is running, check the fluid level in the reservoir and add fluid as recommended. Also, the leg valve might be inoperative, requiring cleaning, repair, or replacement. Finally, check for a lost electronic signal between the control and leg valves by tracing wires for voltage drop or signal loss, repairing or replacing wires, or replacing the touchpad if necessary.
What to do if Lippert Components LCI Level-Up Control Systems alarm sounds and 'Jacks Down' light flashes while traveling?
If the alarm sounds and the 'Jacks Down' light flashes while traveling, even though the jacks are fully retracted on your Lippert Components Control Systems, it could be due to low fluid level. Add fluid as recommended. Alternatively, the retract press switch may be inoperable; check the connection or replace it.
Why Lippert Components Control Systems jacks will not retract?
If one or two jacks on your Lippert Components Control Systems won't retract, the hose may be damaged or unconnected; replace or reconnect it. The valve could also be inoperative and require replacement. If there's a loss of electronic signal between the control and solenoid, try retracting the jacks in MANUAL mode. If successful, replace the touchpad. If not, test for voltage drop between the touchpad and leg valve, repairing bad wiring or replacing the defective board or valve.
Why 'Jacks Retracted' does not display on Lippert Components LCI Level-Up Control Systems?
If the 'Jacks Retracted' message doesn't display when all jacks are retracted on your Lippert Components Control Systems, it could be due to low fluid level. Add fluid as recommended. Alternatively, the retract press switch may be inoperable; check the connection or replace it.
How to troubleshoot Lippert Components Control Systems touchpad with no power?
If there is no power to the touchpad on your Lippert Components Control Systems, check if the circuit breaker has tripped and reset it. Also, ensure the ignition is turned ON.
What does 'Low Voltage' mean on Lippert Components LCI Level-Up Control Systems touchpad?
If the touchpad powers up but displays 'Low Voltage' on your Lippert Components Control Systems, start the coach engine.
Why Lippert Components Control Systems jack bleeds down after being extended?
If a jack bleeds down after being extended on your Lippert Components Control Systems, the valve manual override may be open. Close the override.
Conditions for safe operation and pre-checks.
Overview of the electric/hydraulic leveling system.
Recommended fluid type and cold weather considerations.
Regular checks and cleaning for system longevity.
Explains the function of each button on the touch pad control.
Step-by-step guide to setting the system's zero point.
Specific instructions for diesel units with air bag systems.
How the system signals errors and malfunctions.
General operational notes and system behaviors.
System behavior and limitations when voltage is low.
Conditions that trigger the "Excess Angle" error.
Explains various error messages and their causes.
Guidance on choosing a suitable location for leveling.
Steps to initiate and perform automatic leveling.
How the system extends and levels the coach automatically.
Step-by-step guide for manual operation of leveling jacks.
How to retract jacks automatically or manually.
Using a hex wrench to manually move jacks.
Method to extend/retract jacks with a drill.
How the system powers down after inactivity.
System response when ignition is on and jacks are down.
Triggers and response to the alarm.
General| Brand | Lippert Components |
|---|---|
| Model | LCI Level-Up |
| Category | Control Systems |
| Language | English |
To Next Page
