Programming the HomeLink
Buttons
Note that lhe
best
programming
€sulis will be achieved
il
the existing rcmote controller for
lhe device is fitted with new
batls es. Apply ihe vehicle
parking
bmk€ and switch on the
ignition,
butdo not starllhe engine. The Homelink
controlpanel
is localed in lhe rcofpanelbelween
the sun visors.
1. Press
and hold lhe two outsr buttons
(land
lll)onthe
control
panelfor
about 20 seconds
untilthe adjacent LED begins to
flash.
Note; This
procedure
erases
any factory-set default cod€s and
does not have to befollowed to
programtheother
Homelink
2. Holdthe
originalrcmote contrclof the
device ata distance of
betw€en 50and 300mm from
lhe Homelink
panel,
k€eping the
LED inview Theoplimum distance will
depend on the char-
acte slics of the
particular
system being
programmed,
such
lhal several attempts may be needed
at varying distances.
Maintain each
position
for at least 30 s€conds befoe trying
3- ljsing
bolh hands, simullaneously
push
the remole
control
button a,'rd the desned HomeLank
button. Do not release
lhe
buttons untilstep4 has been completed.
4. The Hom€Link LED will
flash, irsl slowly, and then, wh€n it
begins
to flash rapidly
(indic€ling
successtul
progamming),
release both buttons.
The butun is nowprcgrammed,
and should ope€te1h6 devic€
in €xaclly the
sameway as the orisinalrcmote control. When
the
Homelink
button is
pressed,
the LED will light
constantly and the
device will operate. For
convenience, the original remote contrcl
may also
be used, and should in any case be kept for any future
programming
Gquir€ments
(e.9.
change ol vehicle).
lf HomeLink does
not now operate, and the Homelink LED
flashes
quickly
for a short
pe
od and ihen
stays on constantly
for2 seconds, this is an lndjcation
that the device opetales using
a Rolling
Code ieaturc, and must be synchronised
as follows.
Note thal this
procedure
willbe
easierwith the aid of a second
Rolling
Code Synchroni6ation
1. Locateth6tra ning butlon
(progrcmming
button)onthe
gatoor
garage
door
opener motorhead unit. The location and colour
ofthe butlon willvary accordinq to the
device manuiacturcr
Refer also to the manufacturels instructions
Training ad-
dilional remote contmls'.
2. Press
the lraining butlon on the device, which will usually
activate an associated light.
Note;You now
have typically 30seconds in which to initiate
slep 3.
3. Fimly
press
and then release the
prog€mmed
Homelink
button. Press and release the Homelink button a second
tim€ to complete
the trainang
process.
Some devices may
require
a lhird button
press
lo complele lhe lrarnrng.
The
gate
ordooropenershould now recognisethe HomeLink
signaland activate when
the HomeLank button is
prcssed.
The
other two HomeLink buflons may now be
progEmmed
to other
devices in
a
similar
way.
Reprogramming
a Single HomsLink Button
lf a Homelink button has been
programmed
lo aclivate a
device, and
you
now wish lo use this buflon to opetate a differenl
devic€,
proc€ed
as follows- This
procedue
will erase the exisling
programming
ol the respective Homelink button.
1. Press and hold lhe appropriale
HomeLink button forabout 20
seconds untilthe LED slarts flashing slowly. Do not release
unlilstep 4 has been completed.
2. Ho d the odginal remote control of lh€ d€vice at a distance
of
belw€en 50 and
300mm
from
lhe controlpanel. The optimum
distance will depend on the characteristics of the
particular
system being
prcgtammed,
such
that severalatlempts may
be needed al varying
distances. Maintain each
position
for
at least 30 seconds befor€ trying another.
3. Prsss and hold the device remote
conlrol button.
4. The Homelink
LED will flash slowly. When th€ flashing
becomes rapid
(indicating
successful
progamming),
release
both the device
and
Homelink
buttons,
Any sysiem
previously programmed
to the Homelink button
is nowerased,
and the new system is ready for operation- This
prccess
has no effect
on the other
Homelink
butlons.
Homelink Button Programme E16sure
Ihe Homelink
bultons c€n be rcprogrammed individually
(see
above) but not individually
de-programmed. To erase the
To Next Page
