Need help?Do you have a question about the M Squared SolsTiS and is the answer not in the manual?
General| Linewidth | <1 MHz |
|---|---|
| Beam Quality (M²) | <1.1 |
| Control Interface | Ethernet, USB |
| Polarization | Linear |
| Weight | 15 kg |
| Power Requirements | 100-240 VAC, 50-60 Hz |
General safety advice, including warnings about user-serviceable parts and grounding.
Details laser hazards, precautions, and warning labels for Class IV lasers.
Information about protective housings and their importance for laser system safety.
Explains the remote interlock circuit for pump laser safety.
Describes the laser emission warning indicator and its function.
Details the function of the internal shutter for blocking laser emission.
Explains the purpose of the key switch for preventing unauthorized use.
Describes the manual reset procedure after power interruption or interlock trip.
Details the RoHS Directive's restrictions on hazardous substances in electronic products.
Explains the SolsTiS laser's tuneable CW output, design, and ease of use.
Lists the typical components included with the SolsTiS system.
Presents standard specifications for different SolsTiS models and linewidth options.
Explains the principles of operation behind the SolsTiS Ti:Sapphire laser.
Describes the Ti:Sapphire gain medium and its properties relevant to laser emission.
Explains how lasers oscillate on cavity modes and longitudinal modes.
Details the SolsTiS cavity design, including features for narrow linewidth operation.
Provides important warnings and references for operating the pump laser.
Describes the sealed, hands-free SolsTiS laser head and its computer-controlled operation.
Notes that the laser head has no external controls; operation is via PC software.
States that the laser head has no embedded indicators; status is shown in software UI.
Details the electrical connections to the SolsTiS laser head.
Describes the Pump Optics Module (POM) used for routing and aligning the pump beam.
Explains manual adjustment of POM mirrors for pump beam alignment.
Details the SolsTiS control unit, its ICE-BLOC platform, and Ethernet connectivity.
Lists indicators and connections for the wavelength control unit.
Notes controls are via software UI and netbook, apart from AC Power I/O.
Explains Ethernet connection and use of the SolsTiS software UI via a web browser.
Discusses the water chiller for high-power pump lasers and its installation.
Instructions for inspecting and unpacking the system components.
Overview of the straightforward setup and operation of the SolsTiS system.
Factors and precautions for planning the installation and placement of the system.
Grouped warnings on voltage selection, controller placement, and optical fiber handling.
Grouped cautions on laser head weight, PC usage, and netbook PC usage.
Step-by-step guide for connecting and activating the SolsTiS wavelength control unit.
Explains network addressing and Ethernet connection for software control.
Details network addressing (MAC, IP) and the role of DHCP in network setup.
Notes that the laptop and control unit are pre-configured with fixed IP addresses.
Guides users through connecting the laptop to the control unit and accessing the UI.
Lists password levels and typical default settings for system access.
States no internal optical alignment is needed due to the laser's design.
Steps for initial system start-up and activating the laser system.
Guides for initial coarse alignment of the pump laser to the SolsTiS head.
Steps for mounting and coarsely aligning an integrated pump laser.
Steps for coarsely aligning a separate, non-integrated pump laser.
Procedure for checking and optimizing pump beam alignment at low power.
Explains how to tune and scan the SolsTiS laser's output wavelength.
Guides on using the BRF Tune control for coarse wavelength adjustment.
Details fine-tuning wavelength using the Etalon Tune adjustment.
Explains how to lock the etalon to achieve single longitudinal mode operation.
Guides on locking and adjusting the reference cavity for fine frequency tuning.
Explains how to scan SolsTiS frequency by adjusting the reference cavity.
Describes the continuous scan mode for wavelength scanning.
Describes the single scan mode for wavelength scanning.
Describes the cavity ramp scan for small frequency range scans.
Describes the modulate function for diagnostic purposes.
How to permanently store user settings via the Save Data button.
Instructions for shutting down the laser system and the chiller.
Guidance on purging the SolsTiS laser head with dry nitrogen.
Grouped warnings about covers, voltages, laser hazards, contamination, and manual adherence.
Outlines recommended maintenance tasks, including cleaning and periodic checks.
Grouped notes on cleaning, safety feature verification, and chiller maintenance.
How to monitor photodiodes and system voltages using the Monitor Out MCX.
Provides tips for troubleshooting common issues with the SolsTiS laser system.
Grouped notes on consulting manuals and warnings about optics cleaning.
Addresses troubleshooting steps for a drop in SolsTiS output power.
Grouped warnings and cautions on handling, inspecting, and cleaning laser optics.
Advice on when cleaning laser optics is necessary and the risks involved.
Specific procedure for cleaning the SolsTiS laser head output window.
Warnings about changing pump lasers and notes on list accuracy and compatibility.
Describes the Resonator Fast input for frequency modulation and its characteristics.
Describes the Resonator Slow input for scanning the laser over its full tuning range.
Describes the Reference Cavity input for external tuning/scanning.
To Next Page