Sound modes and surround parameters
Sound mode
Surround Parameter
Subwoofer Level
Adjust
Cinema EQ
Loudness
Management
z1
Dynamic
Compression
z2
Low Frequency
z3
Speaker Select Center Spread Center Gain
Direct/Pure Direct (2-channel) z4 Sz5 SS
Direct/Pure Direct (Multi-channel) z4 S SSS
DSD Direct (2-channel)
Sz5
DSD Direct (Multi-channel) z4 S S
Stereo
S SS
Multi Ch In
SS S
Dolby Surround
SSSS S
DTS Neo:X
SSSS S S
Audyssey DSX®
SSSSS
Dolby Digital
SSSSS
Dolby Digital Plus
SSSSS
Dolby TrueHD
SSSSS
Dolby Atmos
SSSSS
DTS Surround
SS SS
DTS 96/24
SS S
DTS-HD
SS S
DTS Express
SS S
Multi Ch Stereo
S SSSS
z
1 -
z
5 : “Sound modes and surround parameters” (v p. 292)
Contents Connections Playback Settings Tips Appendix
290
Front panel Display Rear panel Remote Index
Sound mode
Dialog
Enhancer
Tone
z6
Audyssey
M-DAX
z9
Bass Sync
z10
MultEQ® XT32
z7
Dynamic EQ
z8
Dynamic
Volume
z8
Audyssey
LFC
TM
z8
Audyssey DSX®
Direct/Pure Direct (2-channel) z4
Direct/Pure Direct (Multi-channel) z4
DSD Direct (2-channel)
DSD Direct (Multi-channel) z4
Stereo
SSSSSS S
Multi Ch In
SSSSSSS S
Dolby Surround
SSSSSS S
DTS Neo:X
SSSSSS S
Audyssey DSX®
SSSSSSS S
Dolby Digital
SSSSSSS S
Dolby Digital Plus
SSSSSSS S
Dolby TrueHD
SSSSSSS S
Dolby Atmos
SSSSSS S
DTS Surround
SSSSSSS S
DTS 96/24
SSSSSSS S
DTS-HD
SSSSSSS S
DTS Express
SSSSSSS S
Multi Ch Stereo
SSSSSS SS
Virtual
z
1 - 3、
z
7 -
z
10 : “Sound modes and surround parameters” (v p. 292)
Contents Connections Playback Settings Tips Appendix
291
Front panel Display Rear panel Remote Index
z
1
This item can be selected when the Dolby Digital, Dolby Digital Plus, Dolby TrueHD or Dolby Atmos signal is played back.
z2
This item can be selected when the Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos or DTS is played back.
z3
This item can be selected when a Dolby Digital or DTS signal or DVD-Audio is played.
z4
During playback in Pure Direct mode, the surround parameters are the same as in Direct mode.
z5 This setting is available when “Subwoofer Mode” in the menu is set to “LFE+Main”. (v
p. 225)
z6 This item cannot be set when “Dynamic EQ” is set to “On”. (v
p. 174)
z7
This item cannot be set when Audyssey
®
Setup (Speaker Calibration) has not been performed.
z8
This item cannot be set when “MultEQ
®
XT32” in the menu is set to “Off”. (v p. 174)
z9
This item can be set when the input signal is analog, PCM 48 kHz or 44.1 kHz.
z10
This can be set when the LFE signal is included in the input signal.
Contents Connections Playback Settings Tips Appendix
292
Front panel Display Rear panel Remote Index
92
To Next Page
Loading...
