Why can't I select Pro Logic II mode on my Marantz Receiver?
If you cannot select Pro Logic II mode on your Marantz Receiver, the input signal might be incompatible. Use a 2 channel Dolby Digital input signal, PCM input signal, or analog input signal.
Why can't I select EX/ES mode on my Marantz Receiver?
If you cannot select EX/ES mode on your Marantz Receiver, it could be because: * Surround center= NONE has been selected in SPEAKERS SIZE SETUP. Make the correct setting. * The input signal is incompatible. Use a 5.1 channel source.
What causes noise during FM reception on my Marantz Receiver?
If you're hearing noise during FM reception on your Marantz Receiver, it could be due to weak radio waves from the broadcasting station. Consider installing an FM outdoor antenna.
What to do if my Marantz Receiver has no sound and picture even when power is on?
If your Marantz Receiver isn't producing any sound or picture even when powered on, there are several potential causes: * The mute function might be activated. Try canceling mute using the remote control. * The input cable may not be properly connected. Refer to the connection diagram to ensure correct cable connections. * The master volume could be turned down completely. Adjust the master volume to an audible level. * The function selector might be set to the wrong position. Select the correct input position.
Why is the sound coming from the wrong channel on my Marantz Receiver?
If the sound from your Marantz Receiver is coming from the wrong channel, the speaker cable may be connected incorrectly. Refer to the connection diagram and connect the cable correctly.
Why is my Marantz Receiver playing sound from the wrong input?
If your Marantz Receiver is outputting sound and pictures from equipment other than what's selected with the function selector, it could be due to an incorrectly connected input cable. Refer to the connection diagram and ensure the cable is connected correctly.
What to do if my Marantz SR7300 Stereo Receiver FM or AM reception fails?
If the FM or AM reception fails, correctly connect the indoor FM and AM antennas to the FM and AM antenna outlets.
Why is there no sound from the surround back speaker on my Marantz SR7300?
If there's no sound from the surround back speaker, check these: * Ensure the surround back speaker cable connection is complete. * Confirm that the Surround mode is set to EX/ES. * Verify that 'Surround back = NONE' has not been selected in SPEAKERS SIZE SETUP; if so, make the correct setting.
Why does my Marantz SR7300 Stereo Receiver not output any sound from the center speaker?
If there is no sound coming from the center speaker, check the following: * Ensure the center speaker cable is correctly connected. * If 'STEREO' is selected for Surround mode, no sound will be output from the center speaker; select another Surround mode. * Confirm that 'Center = NONE' has not been selected in SETUP mode; if so, make the correct setting.
Why does my Marantz Stereo Receiver not output any sound from the surround speakers?
If no sound is coming from the surround speakers, it could be due to a few reasons: * Check if the surround speaker cable connection is properly connected. * If 'STEREO' is selected for Surround mode, no sound will be output from the surround speakers. Try setting another Surround mode instead. * Verify that 'Surround = NONE' has not been selected in SETUP mode; if so, make the correct setting.
General| Type | Stereo Receiver |
|---|---|
| Total Harmonic Distortion (THD) | 0.08% |
| Signal-to-Noise Ratio | 100 dB |
| Input Sensitivity | 200 mV |
| Headphone Output | Yes |
| Power Output | 100 W per channel (8 ohms) |
| Frequency Response | 10 Hz - 100 kHz |
| Input Impedance | 47k ohms |
| Digital Inputs | Coaxial, Optical |
| Analog Inputs | 6 |
| Analog Outputs | 1 |
| Tuner Section | AM/FM |
To Next Page
