How to fix incline motor disconnection in Matrix 7xe Music Mixer?
If the incline motor is disconnected in your Matrix Music Mixer, check the incline motor wire connection between the incline and LCB. Then, check the incline motor VR for data. If there’s no data, replace the incline motor. If there’s data, replace the LCB.
What to do if incline motor operation fails in Matrix 7xe?
If the incline motor operation fails on your Matrix Music Mixer, run Auto Calibration. If the error code occurs during Auto-calibration, the machine can still work, so no action is needed. However, if the error code appears during a workout, replace the incline motor.
Why does my Matrix 7xe Music Mixer show an incline calibration error?
An incline calibration error on the Matrix Music Mixer can occur if the calibration time is too long or the calibration distance is too short. To resolve this, avoid fixing the incline motor tube when turning on the power. If the console continues to display error code 01A1, replace the incline motor. If auto calibration completes, follow the incline motor installation SOP to secure the incline motor. Alternatively, the error may require replacing the LCB.
What to do if resistance disconnects in Matrix 7xe Music Mixer?
If there's a resistance disconnect issue with your Matrix Music Mixer, check if the resistance is short circuit. If resistance data is under 10 ohms, replace the power resistance. If resistance data is over 10 ohms, replace the LCB.
How do I resolve an encoder error on my Matrix 7xe Music Mixer?
If you're encountering an encoder error on your Matrix Music Mixer, check the connection of the speed sensor cable from the LCB to the speed sensor. Also, check if LED D35 on the LCB is on when the brake is turned to the left release position. If LED D35 is off, move the stairs about 3 stairs and check to see if LED D35 is flashing. If not, replace the speed sensor. If yes, adjust the speed sensor position and clean the speed sensor of any debris, then re-test.
What causes incline motor over current in Matrix Music Mixer?
If the incline motor in your Matrix Music Mixer is experiencing over current, avoid fixing the incline motor tube before turning on the power. If the console still displays an error, replace the incline motor. If the console does not show an error, follow the incline motor installation SOP to fix the incline motor. If the issue persists, replace the LCB.
How to fix Electro magnet disconnected in Matrix Music Mixer?
If the Electro-magnet (ECB) is disconnected in your Matrix Music Mixer, check if it is short-circuited or open. If the resistance data shows a short/open ohms or is outside the range of 12.8 ~ 14.2 ohms, replace the Electro-magnet. If the resistance data is in the range between 12.8 ~ 14.2 ohms, replace the LCB.
What to do for Electro magnet over current in Matrix 7xe Music Mixer?
If the Electro-magnet (ECB) in your Matrix Music Mixer is experiencing over current, check if the Electro-magnet is short-circuited or open. If the resistance data indicates a short/open ohms or falls outside the range of 12.8 ~ 14.2 ohms, replace the Electro-magnet. If the resistance data is within the range of 12.8 ~ 14.2 ohms, replace the LCB.
How to fix Matrix 7xe MCB over temperature?
If the MCB in your Matrix Music Mixer is overheating, check if both fans are working correctly. There's a fan mounted to the MCB itself, as well as an external fan. Also, check the fan connections at the MCB. If the fans are running correctly, replace the MCB.
What to do if Matrix 7xe Music Mixer has low AC power input voltage?
If your Matrix Music Mixer shows a low AC power input voltage when the motor is running, verify that the input power is within the normal range (110V: below 76V / 220V: below 186V). If the input power is within range, replace the MCB.
General| Brand | Matrix |
|---|---|
| Model | 7xe |
| Category | Music Mixer |
| Language | English |
Details dedicated circuits, grounding, and power for safe unit operation.
Detailed breakdown of settings and parameters within Manager Mode.
Overview of settings and configurations available in Engineering Mode.
Comprehensive list of service parameters and their values.
Visual representation of the console's internal electrical connections.
List of error codes, descriptions, and solutions for troubleshooting.
Process for updating the console software using a USB drive.
To Next Page
