EasyManua.ls Logo

Maytag W10393006 - User Manual

Maytag W10393006
52 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
PAGE 1
FOR SERVICE TECHNICIAN’S USE ONLY
DO NOT REMOVE OR DESTROY
IMPORTANT SAFETY NOTICE — “For Technicians only”
This service data sheet is intended for use by persons having electrical, electronic, and
mechanical experience and knowledge at a level generally considered acceptable in the
appliance repair trade. Any attempt to repair a major appliance may result in personal injury
and property damage. The manufacturer or seller cannot be responsible, nor assume any
liability for injury or damage of any kind arising from the use of this data sheet.
Maytag Control Panel ........................................... 2
Diagnostic Guide .................................................. 3
Service Diagnostic Mode ...................................... 3
User Interface/Control System Test ....................... 4
Install Diagnostics ................................................ 5
Software Version Display ...................................... 6
Fault/Error Codes ............................................. 6, 7
Contents
Troubleshooting Guide .......................................... 8
Troubleshooting Tests..................................... 9–21
Resetting Modifiers & Options ............................ 21
Strip Circuits ...................................................... 22
Component Locations ........................................ 23
Specifications .................................................... 23
Wiring Diagrams .......................................... 24, 25
PART NO. W10393006B
IMPORTANT: Electrostatic Discharge (ESD) Sensitive Electronics
ESD problems are present everywhere. Most people begin to feel an ESD discharge at
approximately 3000V. It takes as little as 10V to destroy, damage, or weaken the main control
assembly. The new main control assembly may appear to work well after repair is finished,
but a malfunction may occur at a later date due to ESD stress.
Use an anti-static wrist strap. Connect wrist strap to green ground connection point or
unpainted metal in the appliance
-OR-
Touch your finger repeatedly to a green ground connection point or unpainted metal
in the appliance.
Before removing the part from its package, touch the anti-static bag to a green ground
connection point or unpainted metal in the appliance.
Avoid touching electronic parts or terminal contacts; handle electronic control assembly
by edges only.
When repackaging main control assembly in anti-static bag, observe above instructions.
Voltage Measurement Safety Information
When performing live voltage measurements, you must do the following:
Verify the controls are in the off position so that the appliance does not start when energized.
Allow enough space to perform the voltage measurements without obstructions.
Keep other people a safe distance away from the appliance to prevent potential injury.
Always use the proper testing equipment.
After voltage measurements, always disconnect power before servicing.

Table of Contents

Questions and Answers

  • N
    nguyenscottAug 15, 2025
    Why won't my Maytag Dryer start?
    • A
      Angela HernandezAug 15, 2025
      Your Maytag dryer might not start because the door isn't fully closed, so make sure it is completely closed and then press and hold the 'start' button. Another potential cause is a problem with the door switch, drive belt, belt switch, thermal fuse, or even the motor. A user interface or CCU problem could also be the reason.
  • E
    Elizabeth BrownAug 18, 2025
    Why does my Maytag W10393006 Dryer not power up?
    • C
      Christopher CarterAug 18, 2025
      If your Maytag dryer isn't powering up, with no keypad response or LEDs, the issue could be due to several reasons. First, check the power at the outlet, circuit breaker, fuses, and junction box connections. There might also be a connection problem between the AC plug and the dryer, or between the CCU and UI. It's also possible that there are no power supplies present at the machine electronics, or that there's a user interface problem.
  • H
    hdavisAug 22, 2025
    Why Maytag Dryer drum will not spin?
    • B
      barbara17Aug 22, 2025
      The drum of your Maytag dryer might not spin due to a drive belt or belt switch problem. It could also be a thermal fuse issue (for electric dryers only), a faulty door switch, a motor problem, or a CCU problem.
  • T
    Timothy AlvaradoAug 26, 2025
    How to fix Maytag Dryer that won't heat?
    • J
      Jasmine TaylorAug 26, 2025
      If your Maytag dryer isn't heating, first verify proper dryer installation. Then, check for L1 and L2 by performing CCU L1 and L2 tests under Install Diagnostics. The problem could also stem from a heater system malfunction, an open heater coil, or a CCU problem.
  • K
    Kathleen JonesAug 28, 2025
    Why does my Maytag W10393006 shut off before clothes are dry?
    • P
      pwongAug 29, 2025
      Your Maytag dryer might be shutting off before the clothes are completely dry because of the dryness setting for auto cycles; try increasing the drying times for one or more auto cycles. A full lint screen or clogged heater vent can also cause this issue, so clean them if necessary. Other potential causes include a moisture sensor problem, or the need to adjust the Customer Focused Dryness Level.
  • T
    Taylor ChenSep 1, 2025
    What to do if Maytag W10393006 won't turn off?
    • R
      richard57Sep 1, 2025
      If your Maytag dryer won't shut off when expected, it could be due to poor airflow, so check the lint screen and exhaust vent and clean them if necessary. Also, check the 'pause/cancel' button by performing a UI Component Test under Component Activation. A moisture sensor, thermistor, user interface, or CCU problem could also be the cause.
  • M
    Matthew FryeSep 4, 2025
    Why is my Maytag W10393006 heating in the air cycle?
    • T
      Tyler OconnorSep 4, 2025
      If your Maytag dryer is heating in the air cycle, it could be due to a shorted heater coil or a shorted heater relay. It may also indicate a heater system problem.
  • J
    Joseph LaneSep 7, 2025
    Why is the Maytag Dryer console not accepting selections?
    • J
      janetwhiteSep 8, 2025
      The console of your Maytag dryer might not be accepting selections because the user is selecting an invalid option, refer to the 'Use and Care Guide'. It could also be a user interface problem.
  • Q
    qwoodsSep 12, 2025
    Why is the water valve on my Maytag W10393006 Dryer not dispensing?
    • C
      Christopher NewmanSep 12, 2025
      The water valve in your Maytag dryer might not be dispensing because a steam cycle hasn't been selected, so refer to the 'Use and Care Guide'. Also, verify the water supply is turned on.

Summary

Safety and General Information

Voltage Measurement Safety

Guidelines for safe voltage measurement procedures, including precautions for electrical hazards.

ESD Precautions

Handling sensitive electronics to prevent electrostatic discharge damage.

Important Safety Notice

Technician's disclaimer and liability notice for using the service data sheet.

Control Panel Overview

Description of the dryer's control panel, buttons, and indicators.

Diagnostic Modes and Procedures

Diagnostic Mode Overview

How to activate and use service diagnostic modes for testing.

System and Install Diagnostics

Tests for UI, controls, installation diagnostics, and software versions.

Fault;Error Code Management

Displaying, advancing, clearing, and understanding fault/error codes.

Factory Default Reset

Procedure to reset cycle options to factory defaults.

Troubleshooting Guide and Tests

Troubleshooting Guide

Guide for diagnosing common dryer problems by symptom.

Component Troubleshooting Tests

Detailed tests for CCU, supply, motor, heat, sensors, and valves.

Technical Reference Materials

Component Locations and Specifications

Visual guide to component placement and technical dryer specifications.

Wiring Diagrams

Electrical wiring schematics for electric and gas dryer models.

Notes

General Notes

General notes section.

Maytag W10393006 Specifications

General IconGeneral
BrandMaytag
ModelW10393006
CategoryDryer
LanguageEnglish

Related product manuals