Maytronics MCC6 - User Manual

Questions and Answers

M
marvindeckerAug 18, 2025
What to do if my Maytronics Vacuum Cleaner does not move?
- N
  Nicholas RoyAug 18, 2025
  If your Maytronics Vacuum Cleaner isn't moving, first, ensure the power supply is plugged in and switched ON, and that the cable is securely connected to the power supply. Next, verify the power outlet is working correctly and hasn't tripped the breaker. If it still doesn't work, try turning the power supply off, waiting 30 seconds, and then turning it back on. Finally, unplug the power supply, open the impeller cover, and check for any obstructions in the impeller.
M
Michael ThompsonAug 21, 2025
Why my Maytronics Vacuum Cleaner moves but doesn't clean the pool?
- D
  Danielle SandersAug 21, 2025
  If your Maytronics Vacuum Cleaner moves but doesn't clean, start by cleaning the filter bag/cartridge. After the cleaner starts moving, observe it for a few minutes to ensure it keeps moving. If it stops, inspect the impeller and drive system for any stuck debris.
W
William HarrisAug 23, 2025
How to fix a Maytronics Vacuum Cleaner that cleans only part of the pool?
- M
  Molly McdowellAug 23, 2025
  If your Maytronics Vacuum Cleaner only cleans part of the pool, ensure there's enough slack in the cable to reach the entire pool area. Also, clean the filter bag/cartridge. Check the brushes to see if they are obstructed or worn out.
J
jennifer79Aug 26, 2025
Why doesn’t my Maytronics Vacuum Cleaner climb the walls?
- M
  meganclineAug 26, 2025
  If your Maytronics Vacuum Cleaner isn’t climbing the walls, begin by cleaning the filter bag/cartridge. Check the chemical levels in the water, as improper levels can cause algae growth, making the walls slippery; adjust the levels and scrub the walls if needed. Also, check that the brushes aren’t worn out and confirm that the wall climbing mode hasn’t been cancelled via the remote control unit (MTC6 only).
R
Rebecca KrauseAug 28, 2025
How to remove kinks from Maytronics Vacuum Cleaner cable?
- L
  Lauren OlsonAug 28, 2025
  To remove kinks from your Maytronics Vacuum Cleaner cable, stretch the cable out completely and let it sit in the sun for at least a day. Also, for MCC6 models only: push in the float on the non-cable side.
W
wwalshAug 30, 2025
What to do if my Maytronics Vacuum Cleaner floats instead of sitting on the pool floor?
- J
  Jocelyn ConnerAug 31, 2025
  If your Maytronics Vacuum Cleaner is floating instead of sitting on the pool floor, try removing the air again. Also, with the Pool Cleaner in the water, squeeze the combined brush/Wonder brush to make sure that they are completely water absorbent.
J
Janet JimenezSep 2, 2025
What to do if my Maytronics Swimming Pool Vacuum moves but doesn't clean?
- W
  William WhiteSep 2, 2025
  If your Maytronics Swimming Pool Vacuum is moving but not cleaning, start by cleaning the filter bag or cartridge. After the cleaner starts, watch it for a few minutes to ensure it keeps moving. If it stops, inspect the impeller and drive system for any stuck debris.
A
amyvaughnSep 5, 2025
Why is my Maytronics MCC6 not moving?
- S
  Shawn BurgessSep 5, 2025
  If your Maytronics Swimming Pool Vacuum isn't moving, verify that the power supply is plugged in and turned on, and that the cable is securely connected to the power supply. Also, ensure the power outlet is working and hasn't tripped a breaker. Try turning the power supply off, waiting 30 seconds, and then turning it back on. Finally, unplug the power supply, open the impeller cover, and check for any trapped objects.
S
scottkingSep 7, 2025
How to fix Maytronics MCC6 Swimming Pool Vacuum that cleans only part of the pool?
- R
  Robin TaylorSep 7, 2025
  If your Maytronics Swimming Pool Vacuum only cleans part of the pool, ensure there's enough slack in the cable for it to reach all areas. Clean the filter bag or cartridge. If you have an MCC6 model, push in the float on the cable side (see figure A). Also, inspect the brushes for obstructions or wear.
M
Michael StephensSep 10, 2025
Why doesn’t my Maytronics MCC6 climb the walls?
- T
  tjohnsonSep 10, 2025
  If your Maytronics Swimming Pool Vacuum doesn’t climb the walls, first clean the filter bag or cartridge. Check the chemical levels in the water, as improper levels can cause algae growth, making the walls slippery; adjust the levels and scrub the walls if needed. Also, inspect the brushes for wear. For MTC6 models, ensure the wall climbing mode hasn’t been disabled via the remote control unit.

Summary

Introduction to the Robotic Pool Cleaner

Robotic Pool Cleaner Specifications

Warnings and Cautions for Safe Operation

Safety Warnings

Essential safety precautions and guidelines for operating the robotic pool cleaner safely and effectively.

Operational Cautions

Recommended water parameters and storage conditions for optimal performance and longevity of the cleaner.

Pool Cleaner Components Overview

Using the Pool Cleaner

Initial Setup Guide

Step-by-step instructions for initial preparation, including cable management and brush preparation.

Placing Cleaner in Pool

Procedure for safely submerging the cleaner, ensuring proper air release and cable management.

Removing Cleaner from Pool

Safe method for retrieving the cleaner from the pool using the handle, avoiding cable strain.

Filter Maintenance and Cleaning

Filter Bag Removal and Cleaning

Detailed steps for detaching, cleaning, and reattaching the filter bag for optimal filtration.

Filter Bag Replacement

Guide on how to properly fit and secure a new filter bag onto the cleaner's frame.

Filter Cartridge Cleaning

Instructions for cleaning the reusable filter cartridges to maintain effective debris capture.

Impeller Cleaning Procedure

Procedure to access and clear debris from the impeller for uninterrupted operation.

Offseason Storage Instructions

Troubleshooting Common Issues

Maytronics MCC6 Specifications

General

Weight	24 lbs
Cleaning Cycle Time	1, 1.5, 2, 2.5 hours
Filter Type	Multi-Layer Cartridge
Cable Length	60 ft
Power Supply	24V DC
Caddy	Yes
Type	Robotic
Pool Type	In-ground
Filtration	Ultra-Fine