To Next PageTo Next Page
How to troubleshoot Medela Symphony Breast Pump if it is not running?
If your Medela Breast Pump isn't running, verify the following: * Confirm that the electrical outlet is working or the battery has enough power. * Ensure the device is switched on. * Check that the program card is correctly inserted into the card compartment on the back of the breast pump.
How to clean condensation or milk in tubing of Medela Symphony Breast Pump?
If you notice condensation or milk in the tubing of your Medela Breast Pump, turn off the pump and unplug it from the power source. Wipe the pump with a damp cloth. Clean the tubing, and if necessary, clean the pump kit. Ensure all components are completely dry before reassembling the breast pump and kit.
How to fix an overflow in my Medela Symphony Breast Pump?
If you experience an overflow with your Medela Breast Pump, place the pump set into the bottle holder. Turn off the pump and unplug it from the electrical outlet. Wipe the pump and membrane area with a damp cloth. If milk is in the tubing, remove the tubing, protective membrane, and membrane cap, and clean them. Shake out any water from the tubing and hang it to dry, or run the pump with the tubing attached until dry. If there is condensation in the tubing, let the pump run with the tubing attached until dry. Reassemble the breast pump and accessories when all components are completely dry.
Why does my Medela Breast Pump say 'Invalid card'?
An 'Invalid card' message on your Medela Breast Pump may appear because: 1. The program card is not a Symphony card. If so, check if the correct program card is being used. 2. The program card is incorrectly inserted. If so, check that card is positioned correctly. 3. The program card is damaged and not working. If so, replace program card.
What causes a 'Motor overload' error on a Medela Symphony?
If your Medela Breast Pump shows a 'Motor overload' error, it indicates that the motor is drawing too much current. Contact the rental station if this issue happens repeatedly.
Why is there low or no suction in my Medela Breast Pump?
Low or no suction in your Medela Breast Pump can be caused by incorrect assembly, loose connections, or parts that are not completely dry. Ensure the pump set is assembled correctly, and all connections are secure. Make sure the breast shield forms a complete seal. The tubing ends should be firmly connected to the connector lid and the Symphony cap opening. The Symphony cap must be firmly fitted to the breast pump membrane to create a seal. Check that the membrane is intact and correctly placed in the connector, with the connector lid properly closed. Avoid kinking or trapping the tubing. Ensure all components are completely dry.
What to do if Medela Symphony Breast Pump motor is not running?
If the motor of your Medela Breast Pump isn't running, check the following: Ensure the pump is connected to a power source or that the battery has power. Verify that the device is switched on. Confirm that the program card is correctly inserted into the card compartment located on the back of the breast pump.
Why is there low or no suction with my Medela Symphony?
Low or no suction with your Medela Breast Pump can occur due to several reasons. Ensure you've assembled the pump set according to the instructions. Verify that all connections to the pump set and breast pump are secure. Make sure the breast shield creates a complete seal around the breast. Also, confirm that the pump set components are clean, undamaged, and correctly assembled: * Check that the tubing ends are firmly connected. * Ensure the tubing isn't kinked or trapped during expression. * All components must be completely dry before pumping.
How to fix a Medela Symphony if the motor is not running?
If the motor of your Medela Breast Pump isn't running, verify the following: * Ensure that mains power or battery is available. * Confirm that the device is switched on. * Check that the program card is correctly inserted in the card compartment on the back of the breast pump.
How to troubleshoot Medela Symphony if the motor is not running?
If the motor of your Medela Breast Pump isn't running, first, check if mains power or battery is available. Next, make sure the device is switched on. Finally, verify that the program card is correctly inserted into the card compartment on the back of the breast pump.
General| Type | Hospital-grade electric breast pump |
|---|---|
| Battery Option | No |
| Double Pumping | Yes |
| Technology | 2-Phase Expression Technology |
| Power | 100-240 V, 50/60 Hz |
| Power Source | AC Adapter |
| Compatibility | Compatible with Medela breast shields and bottles |
| Programs | 2-phase expression (stimulation and expression modes) |
| Weight | 7.05 lbs (3.2 kg) |
| Hygiene | Closed system |
Details of the Symphony breast pump's main unit, including LCD and controls.
Steps for connecting the power cord and turning on the Symphony breast pump.
Step-by-step guide for assembling the breast pump kit components.
Guide to testing breast shield fit and selecting the optimal size for comfort.
Essential steps to perform before starting a pumping session, including hand washing.
How to attach pump kit components and set the vacuum level for comfort.
Steps to safely end pumping, disconnect the pump, and store milk.
Instructions for using the Standard Program Card for milk production.
Guide to using the Preemie+ Program Card for milk initiation.
How to use the INITIATE program for milk production initiation.
How to use the MAINTAIN program for ongoing milk production.
Troubleshooting steps for when the breast pump fails to turn on.
Diagnosing and resolving problems related to low or absent suction.
Understanding Symphony error codes displayed on the LCD and their solutions.
