What to do if Millipore Water Filtration Systems says bad Progard type?
If your Millipore Water Filtration System displays 'BAD PROGARD TYPE', check the type of pack being installed. For further assistance, contact Millipore SAS.
How to clear ASM UV lamp exchange overdue message on Millipore Elix 20 Water Filtration Systems?
The 'ASM UV LAMP EXCH. OVERDUE: XX DAYS' message on your Millipore Water Filtration System will disappear once a new ASM UV Lamp is installed and its software timer is reset.
How to clear EXCH. UV lamp in XX days message on Millipore Elix 20?
The message 'EXCH. UV LAMP IN XX DAYS' on your Millipore Water Filtration System will disappear when you install a new UV Lamp and reset the software timer.
What to do if distilled water conductivity is less than mini on Millipore Water Filtration Systems?
If the Millipore Water Filtration System displays 'DIST WATER CONDUCTIVITY < MINI', keep the loop operating for a few minutes to remove any air that could be trapped in the Resistivity Sensor. If problems persist, contact Millipore SAS for assistance.
What to do if the Millipore Water Filtration Systems shows a low feed pressure?
If the Millipore Water Filtration System displays 'LOW FEED PRESSURE', first ensure the feedwater supply is turned on. Next, check if the Progard TL Pack is clogged by observing the RO reject water in FLUSH mode. If the water pressure issue is resolved during FLUSH mode, the alarm will automatically reset.
What to do if Progard TL pack type error appears on Millipore Elix 20 Water Filtration Systems?
If your Millipore Water Filtration System displays 'PROGARD TL PACK TYPE ERROR', check the catalogue number of the Progard TL using its label and replace it if necessary.
How to fix TOC meter error 2 on Millipore Elix 20?
If you encounter a 'TOC METER ERROR 2' on your Millipore Elix System, try turning the system off and then on again. Then, dispense water for several minutes. If the error persists, contact Millipore SAS for further assistance.
How to fix TOC meter error 3 on Millipore Elix 20 Water Filtration Systems?
If you encounter a 'TOC METER ERROR 3' on your Millipore Elix System, try turning the system off and then on again. Then, dispense water for several minutes. If the error persists, contact Millipore SAS for further assistance.
What to do for high pump pressure on Millipore Elix 20 Water Filtration Systems?
To address a 'HIGH PUMP PRESSURE' issue on your Millipore Water Filtration System, try setting the RO Pump Pressure lower. If the problem persists, contact Millipore SAS for additional assistance.
How to fix Progard TL pack not in place error on Millipore Water Filtration Systems?
To resolve the 'PROGARD TL PACK NOT IN PLACE' error on your Millipore Water Filtration System, make sure the Progard TL is installed with its “TAG” at the bottom.
Important safety statements, warnings, and symbols for system operation.
Summary of typical maintenance tasks, frequency, and procedures.
Step-by-step guide for replacing the Progard TL pretreatment pack.
Instructions for replacing the UV lamp within the Elix system.
Methods for sanitizing the RO cartridges, both automatic and manual.
Procedures for cleaning RO cartridges using specific cleaners.
Step-by-step guide for replacing the QGard TL1 Polisher Pack.
Procedures for cleaning the A10 TOC Monitoring Device.
Classification and explanation of different system messages and indicators.
Detailed list of LCD messages, their meanings, and recommended actions.
General| Type | Water Purification System |
|---|---|
| Model | Elix 20 |
| Output Flow Rate | 20 L/h |
| Power Supply | 100-240 V, 50/60 Hz |
| Feed Water Requirements | Potable water |
To Next Page