What to do if Millipore Water Filtration Systems says bad Progard type?
If your Millipore Water Filtration System displays 'BAD PROGARD TYPE', check the type of pack being installed. For further assistance, contact Millipore SAS.
How to clear ASM UV lamp exchange overdue message on Millipore Elix 35?
The 'ASM UV LAMP EXCH. OVERDUE: XX DAYS' message on your Millipore Water Filtration System will disappear once a new ASM UV Lamp is installed and its software timer is reset.
How to clear EXCH. UV lamp in XX days message on Millipore Water Filtration Systems?
The message 'EXCH. UV LAMP IN XX DAYS' on your Millipore Water Filtration System will disappear when you install a new UV Lamp and reset the software timer.
What to do if distilled water conductivity is less than mini on Millipore Water Filtration Systems?
If the Millipore Water Filtration System displays 'DIST WATER CONDUCTIVITY < MINI', keep the loop operating for a few minutes to remove any air that could be trapped in the Resistivity Sensor. If problems persist, contact Millipore SAS for assistance.
What to do if the Millipore Water Filtration Systems shows a low feed pressure?
If the Millipore Water Filtration System displays 'LOW FEED PRESSURE', first ensure the feedwater supply is turned on. Next, check if the Progard TL Pack is clogged by observing the RO reject water in FLUSH mode. If the water pressure issue is resolved during FLUSH mode, the alarm will automatically reset.
What to do if Progard TL pack type error appears on Millipore Water Filtration Systems?
If your Millipore Water Filtration System displays 'PROGARD TL PACK TYPE ERROR', check the catalogue number of the Progard TL using its label and replace it if necessary.
How to fix TOC meter error 2 on Millipore Elix 35?
If you encounter a 'TOC METER ERROR 2' on your Millipore Elix System, try turning the system off and then on again. Then, dispense water for several minutes. If the error persists, contact Millipore SAS for further assistance.
How to fix TOC meter error 3 on Millipore Water Filtration Systems?
If you encounter a 'TOC METER ERROR 3' on your Millipore Elix System, try turning the system off and then on again. Then, dispense water for several minutes. If the error persists, contact Millipore SAS for further assistance.
What to do for high pump pressure on Millipore Elix 35 Water Filtration Systems?
To address a 'HIGH PUMP PRESSURE' issue on your Millipore Water Filtration System, try setting the RO Pump Pressure lower. If the problem persists, contact Millipore SAS for additional assistance.
How to fix Progard TL pack not in place error on Millipore Water Filtration Systems?
To resolve the 'PROGARD TL PACK NOT IN PLACE' error on your Millipore Water Filtration System, make sure the Progard TL is installed with its “TAG” at the bottom.
General operating safety guidelines for the Elix System.
Explains various safety symbols and their meanings.
Details the flow rates and quality parameters of the Elix system's product water.
Lists physical dimensions, weight, operating pressures, environmental, and electrical specs.
Explains how the Elix System delivers water automatically and manually.
Provides a table outlining typical maintenance tasks, their frequency, and how to perform them.
Step-by-step guide for removing and installing the Progard TL pretreatment pack.
Explains automatic and manual methods for sanitising RO cartridges.
Details how to clean RO cartridges using RoClean A or B, and when cleaning is needed.
Provides instructions for replacing the QGard TL1 polisher pack.
Explains the different types of messages (Maintenance, Alarm, Alarm Stop, Custom) and how they are displayed.
Details specific LCD messages, their meanings, and recommended actions.
General| Output Flow Rate | 35 l/h |
|---|---|
| TOC | < 30 ppb |
| Bacteria | < 1 CFU/mL |
| Feed Water Pressure | 1 - 6 bar |
| Feed Water Temperature | 5 - 35 °C |
| Product Water Quality | Type 2 Water |
| Purification Technology | Reverse osmosis |
| Resistivity | > 5 MΩ·cm @ 25 °C |
| Conductivity | < 0.2 µS/cm @ 25 °C |
| Particle Size | < 0.2 µm |
| Feed Water | Potable water |
| Power Supply | 50/60 Hz |
To Next Page