What to do if Millipore Water Filtration Systems says bad Progard type?
If your Millipore Water Filtration System displays 'BAD PROGARD TYPE', check the type of pack being installed. For further assistance, contact Millipore SAS.
How to clear ASM UV lamp exchange overdue message on Millipore Elix 100 Water Filtration Systems?
The 'ASM UV LAMP EXCH. OVERDUE: XX DAYS' message on your Millipore Water Filtration System will disappear once a new ASM UV Lamp is installed and its software timer is reset.
How to clear EXCH. UV lamp in XX days message on Millipore Water Filtration Systems?
The message 'EXCH. UV LAMP IN XX DAYS' on your Millipore Water Filtration System will disappear when you install a new UV Lamp and reset the software timer.
What to do if distilled water conductivity is less than mini on Millipore Elix 100?
If the Millipore Water Filtration System displays 'DIST WATER CONDUCTIVITY < MINI', keep the loop operating for a few minutes to remove any air that could be trapped in the Resistivity Sensor. If problems persist, contact Millipore SAS for assistance.
What to do if the Millipore Water Filtration Systems shows a low feed pressure?
If the Millipore Water Filtration System displays 'LOW FEED PRESSURE', first ensure the feedwater supply is turned on. Next, check if the Progard TL Pack is clogged by observing the RO reject water in FLUSH mode. If the water pressure issue is resolved during FLUSH mode, the alarm will automatically reset.
What to do if Progard TL pack type error appears on Millipore Elix 100 Water Filtration Systems?
If your Millipore Water Filtration System displays 'PROGARD TL PACK TYPE ERROR', check the catalogue number of the Progard TL using its label and replace it if necessary.
How to fix TOC meter error 2 on Millipore Water Filtration Systems?
If you encounter a 'TOC METER ERROR 2' on your Millipore Elix System, try turning the system off and then on again. Then, dispense water for several minutes. If the error persists, contact Millipore SAS for further assistance.
How to fix TOC meter error 3 on Millipore Elix 100 Water Filtration Systems?
If you encounter a 'TOC METER ERROR 3' on your Millipore Elix System, try turning the system off and then on again. Then, dispense water for several minutes. If the error persists, contact Millipore SAS for further assistance.
What to do for high pump pressure on Millipore Elix 100?
To address a 'HIGH PUMP PRESSURE' issue on your Millipore Water Filtration System, try setting the RO Pump Pressure lower. If the problem persists, contact Millipore SAS for additional assistance.
How to fix Progard TL pack not in place error on Millipore Water Filtration Systems?
To resolve the 'PROGARD TL PACK NOT IN PLACE' error on your Millipore Water Filtration System, make sure the Progard TL is installed with its “TAG” at the bottom.
Guidance on how to effectively use the user manual and its contents for system operation.
Critical safety statements, warnings, and symbols to ensure safe operation.
Details on the flow rates and quality parameters of the purified water produced by Elix systems.
Explanation of RO recovery principles and how system recovery is managed.
A visual representation of the Elix system's internal components and water flow path.
In-depth descriptions of the key functional components within the Elix system.
Explanation of the standard operation for delivering purified water, including automatic and manual methods.
A comprehensive table outlining routine maintenance tasks, their frequency, and how-to guides.
Step-by-step instructions for replacing the Progard TL pretreatment pack.
Classification and explanation of different message types displayed by the Elix system.
Detailed guide to interpreting and responding to various alarm and maintenance messages.
General| Type | Water Purification System |
|---|---|
| Water Production Rate | 100 L/h |
| Product Water Flow Rate | Up to 100 L/h |
| Product Water TOC | < 30 ppb |
| Dimensions (H x W x D) | 742 x 640 x 447 mm |
| Weight | 60 kg (empty) |
| Power Supply | 100-240 V ±10% / 50-60 Hz |
| Output Water Quality | Type 2 Water |
| Product Water Resistivity at 25°C | > 5 MΩ·cm |
| Feed Water Quality | Potable water or pre-treated water |
| Technology | Reverse Osmosis with Electrodeionization |
To Next Page