Mindray uMEC10 Service Manual

5. 5.
Select Select
[[
Main MenuMain Menu
] → [] → [
Maintenance >>Maintenance >>
] → [] → [
User Maintenance >>User Maintenance >>
] → [] → [
ModuleModule
Maintenance >>Maintenance >>
] → [] → [
Cal. IBP Press. >>Cal. IBP Press. >>
]. In the []. In the [
Cal. IBP Press.Cal. IBP Press.
] menu, set the] menu, set the
calibration value to 200 mmHg.calibration value to 200 mmHg.
6. 6.
Select Select
the the
[[
CalibrateCalibrate
] button next to the ] button next to the
desired IBP channel to start a calibration.desired IBP channel to start a calibration.
7. 7.
The The
message message
[[
Calibration Completed!Calibration Completed!
]]
is displayed after a successful calibration.is displayed after a successful calibration.
Otherwise, a corresponding message will be Otherwise, a corresponding message will be
displayed.displayed.
Method 2:Method 2:
Tools required:Tools required:

Standard sStandard s
phygmomanomphygmomanom
etereter

Balloon pumpBalloon pump

TubingTubing

T-shape connectorT-shape connector
1. 1.
Connect Connect
the the
3-way 3-way
stopcock, stopcock,
the the
sphygmomanometesphygmomanomete
r ar a
nd the nd the
balloon balloon
pump pump
through through
aa
T-shape connector, as shown below.T-shape connector, as shown below.
2. 2.
Turn on Turn on
the 3-way the 3-way
stopcock to stopcock to
the air the air
to zero to zero
the transthe trans
ducer, aducer, a
nd then nd then
open the open the
stopcockstopcock
to the to the
sphygmomanometersphygmomanometer
..
3. 3.
Select Select
[[
Main MenuMain Menu
] → [] → [
Maintenance >>Maintenance >>
] → [] → [
User Maintenance >>User Maintenance >>
] → [] → [
ModuleModule
Maintenance >>Maintenance >>
] → [] → [
Cal. IBP Press. >>Cal. IBP Press. >>
]. In the []. In the [
Cal. IBP Press.Cal. IBP Press.
] menu, set the target] menu, set the target
pressure calibratipressure calibrati
on value of the target con value of the target c
hannel.hannel.
4. 4.
Inflate Inflate
using the using the
balloon balloon
pump pump
until the until the
reading reading
of sphyof sphy
gmomanometer gmomanometer
approximatesapproximates
the preset calibration value.the preset calibration value.
5. 5.
Adjust Adjust
the the
calibration calibration
value value
in in
the the
[[
Maintain IBPMaintain IBP
] menu until it is ] menu until it is
equal to the readingequal to the reading
of sphygmomanometerof sphygmomanometer
6. 6.
Select Select
the the
[[
CalibrateCalibrate
] button next to the ] button next to the
desired IBP channel to start a calibration.desired IBP channel to start a calibration.
SphygmomanometerSphygmomanometer
T-shape connectorT-shape connector
3-way stopcock3-way stopcock
Pressure transducerPressure transducer
Pressure adapter cablePressure adapter cable
IBP moduleIBP module

Mindray uMEC10 Specifications

General

Resolution	800 x 600
ECG	3/5-lead ECG
EtCO2	Optional
Battery	Rechargeable lithium-ion
Battery Life	4 hours
Dimensions	110 mm
Alarm	Audible and visual alarms
Power Supply	AC 100-240V, 50/60Hz
Agent	No
O2	No