Mitsubishi Electric MELSEC iQ-R Series - Performance Specifications of Power Supply Module

4 SPECIFICATIONS
4.2 Performance Specifications of Power Supply Module
85
4
4.2 Performance Specifications of Power Supply
Module
This section describes the performance specifications of the power supply module.
*1 It will be shorter than 10ms if the input voltage is lower than 24VDC.
Item AC input power supply module DC input power supply module
R61P R62P R64P R64RP R63P R63RP
Input power supply voltage 100 to 240VAC
(85 to 264VAC)
24VDC
(15.6 to 31.2VDC)
24VDC
(19.2 to 31.2VDC)
Input frequency 50/60Hz5% 
Input voltage distortion factor Within 5% 
Maximum input apparent power 130VA 120VA 160VA 
Maximum input power  50W
Inrush current 20A, 8ms or less 100A, 1ms or less (24VDC input)
Rated output current 5VDC 6.5A 3.5A 9A 6.5A
24VDC  0.6A 
Overcurrent
protection
5VDC 7.1A or higher 3.8A or higher 10.0A or higher 7.1A or higher
24VDC  0.66A or higher 
Overvoltage
protection
5VDC 5.5 to 6.5V
Efficiency 76% or more 70% or more
Allowable momentary power failure
time
Within 20ms Within 10ms (24VDC input)
*1
Withstand voltage 2300VACrms per minute (altitude 0 to 2000m),
Between the combined "line input/LG terminals" and the "FG terminal
and output"
510VAC per minute (altitude 0 to
2000m),
between primary terminal and 5VDC
terminal
Insulation resistance 10M or higher by 500VDC insulation resistance tester (between the combined "line input/LG terminals" and the
"FG terminal and output", the line input and LG terminals, the output and FG terminals)
Noise immunity • Noise voltage 1500Vp-p, noise width 1s, noise frequency 25 to 60Hz
(noise simulator condition)
• Noise immunity test IEC 61000-4-4: 2kV
Noise voltage 500Vp-p, noise width 1s,
noise frequency 25 to 60Hz (noise
simulator condition)
Fuse Built-in (user-unchangeable)
Contact output
section
Application ERR
contact
Rated
switching
voltage/current
24VDC, 0.5A
Minimum
switching load
5VDC, 1mA
Response time Offon: 10ms or less
Onoff: 12ms or less
Life Mechanical: 20 million times or more
Electrical: Rated switching voltage/current, 100 thousand times or more
Surge
suppressor
None
Fuse None
Terminal screw size M4 (M3.5 for +24V and 24G terminals of the R62P)
Applicable wire size 0.75 to 2
Applicable solderless terminal RAV1.25-4, RAV2-4, thickness of 0.8mm or less, up to two solderless terminal connections per terminal
(for the +24V and 24G terminals of the R62P: RAV1.25-3.5, RAV2-3.5, thickness of 0.8mm or less, up to two
solderless terminal connections per terminal)
Applicable tightening torque M4 screw: 1.02 to 1.38Nm
M3.5 screw: 0.66 to 0.89Nm
External dimensions Height 106mm (Base unit mounting side: 98mm)
Width 54.6mm
Depth 110mm
Weight 0.41kg 0.45kg 0.46kg 0.41kg