3 REPLACEMENT OF I/O MODULE
3 - 17
(2) Specifications comparison between A1SX10EU and QX10
: Compatible, : Partially changed, : Incompatible
*1 Check the specifications of the sensor or switches to connected to the QX10.
*2 The following shows the derating chart.
Specifications A1SX10EU QX10
Compat-
ibility
Precautions for replacement
Number of input points 16 points 16 points
Isolation method Photocoupler Photocoupler
Rated input voltage 100-120VAC 50/60Hz 100-120VAC 50/60Hz
Input voltage distortion Within 5% Within 5%
Rated input current Approx. 7mA (120VAC 60Hz)
Approx. 8mA (100VAC, 60Hz),
Approx. 7mA (100VAC, 50Hz)
Inrush current
Maximum 200mA Within 1ms
(132VAC)
Maximum 200mA Within 1ms
(132VAC)
Operating voltage range
85 to 132VAC
(50/60Hz±5%)
85 to 132VAC
(50/60Hz±3Hz)
Maximum number of
simultaneous input points
Simultaneously on (100%)
Refer to the derating chart.
*2
Use it within the range shown in
the derating chart.
On voltage/on current 80VAC or more/5mA or more
80VAC or more/5mA or more
(50Hz, 60Hz)
Off voltage/off current 30VAC or less/1.4mA or less
30VAC or less/1.7mA or less
(50Hz, 60Hz)
The off current differs.
*1
Input resistance
Approx. 18k (60Hz)
Approx. 21k (50Hz)
Approx. 12k (60Hz)
Approx. 15k (50Hz)
The input resistance is
reduced.
*1
Response
time
Off on
20ms or less
(100VAC 60Hz)
15ms or less
(100VAC 50Hz, 60Hz)
On off
35ms or less
(100VAC 60Hz)
20ms or less
(100VAC 50Hz, 60Hz)
Common terminal
arrangement
16 points/common
(common terminal: TB9, TB18)
16 points/common
(common terminal: TB17)
Operation indication On indication (LED) On indication (LED)
External connection
system
20-point terminal block connector
(M3.57 screws)
18-point terminal block
(M36 screws)
Wiring change is required.
Applicable wire size
0.75 to 1.25mm
2
(16 to 19 AWG)
Core: 0.3 to 0.75mm
2
(outside diameter: 2.8mm or less)
Applicable solderless
terminal
RAV1.25-3.5
R1.25-3
(Sleeved solderless terminal cannot
be used.)
Current consumption 0.05A (typ. all points on) 0.05A (typ. all points on)
Dielectric withstand
voltage (between batch
external circuits and
internal circuit)
1780VAC rms/3 cycles (altitude
2,000m (6562ft))
1780VAC rms/3 cycles
(altitude 2000m (6562ft))
Insulation resistance
10M or more with an insulation
resistance tester
10M or more with an insulation
resistance tester
Noise immunity IEC801-4: 1kV
• By noise simulator of 1500Vp-p
noise voltage, 1µs noise width,
and 25 to 60Hz noise frequency
• First transient noise IEC61000-4-
4: 1kV
External dimensions 130(H)34.5(W)93.6(D)mm 98(H)27.4(W)90(D)mm Wiring space is narrower.
Weight 0.21kg 0.17kg
(QX10)
100
90
80
70
60
50
40
0102030405055
On
ratio
Ambient temperature
120VAC
132VAC
To Next Page
Loading...
