Mitsubishi Electric Q13UDVCPU - Page 579

577
APPENDICES
A
Appendix 3 List of Special Register Areas
SD1441
Target device 2
setting (iQ Sensor
Solution
backup/restoration)
Sets devices
targeted for
backup/restoration.
This register is used to set a device targeted for
backup/restoration.
[AnyWireASLINK]
0 (Not used)
[CC-Link, CC-Link IE Field Network]
Station sub-ID number
[Ethernet]
IP address (upper 16 bits)
(Example) If the IP address is 192.168.3.40, 192
equals to C0
H
and 168 equals to A8
H
.
The stored value will be C0A8
H
, that is, 49320.
UNew
QnUDV
*1
LCPU
*2
SD1444
Operation setting
(iQ Sensor Solution
backup/restoration)
Sets the operation
status when a
backup/restoration
error occurs
This register stores the operation status of the
CPU module when a backup/restoration error
occurs.
0: Continue
1: Stop
UNew
QnUDV
*1
LCPU
*2
SD1446
Execution status
(iQ Sensor Solution
backup/restoration)
Stores the
backup/restoration
execution status.
This register stores the backup/restoration
execution status.
0
H
: Not executed
1
H
: In preparation
2
H
: Being executed
3
H
: Completed
10
H
: Wait
11
H
: Cancelled (no error)
FE
H
: Cancelled (error)
FF
H
: Error
S (Status
change)
New
QnUDV
*1
LCPU
*2
SD1447
Total number of
target devices (iQ
Sensor Solution
backup/restoration)
Stores the total
number of devices
targeted for
backup/restoration.
This register stores the total number of devices
targeted for backup/restoration for each
execution unit.
• A value is cleared to "0" when the right is
acquired.
S (Status
change)
New
QnUDV
*1
LCPU
*2
SD1448
Number of normally
completed devices
(iQ Sensor Solution
backup/restoration)
Stores the number
of devices where
data are backed up
or restored
successfully.
This register stores the number of devices, for
each execution unit, where data have been
backed up or restored successfully.
• A value is cleared to "0" when the right is
acquired.
S (Status
change)
New
QnUDV
*1
LCPU
*2
SD1449
Number of devices
completed with an
error (iQ Sensor
Solution
backup/restoration)
Stores the number
of devices where
data are not
backed up or
restored
successfully.
This register stores the number of devices, for
each execution unit, where data have not been
backed up or restored successfully.
• A value is cleared to "0" when the right is
acquired.
S (Status
change)
New
QnUDV
*1
LCPU
*2
SD1450
Progress per
device (iQ Sensor
Solution
backup/restoration)
Stores the
progress of the
backup/restoration
processing per
device.
This register stores the progress of the
backup/restoration processing per device in
percentage (0 to 100%).
• A value is cleared to "0" when the right is
acquired.
S (Status
change)
New
QnUDV
*1
LCPU
*2
SD1451
Folder number (iQ
Sensor Solution
backup)
Stores the number
of a folder in which
backup data is
stored.
This register stores the number of a folder in
which backup data is stored.
0 to 99: Folder number
FFFF
H
: Backup data not stored
•FFFF
H
is stored when the right is acquired.
S (Status
change)
New
QnUDV
*1
LCPU
*2
SD1452
Error cause in a
module (iQ Sensor
Solution
backup/restoration)
Stores the cause of
the
backup/restoration
error detected in a
module.
This register stores the cause of the
backup/restoration error detected in a module.
• When errors are detected in multiple devices,
the error detected first is stored.
• A value is cleared to "0" when the right is
acquired.
For details on the cause of the error that is
stored, refer to the following.
Page 411, Appendix 1.11
 User's manual of the module that is targeted
for data backup/restoration
S
(Error/Status
change)
New
QnUDV
*1
LCPU
*2
Number Name Meaning Explanation
Set by
(When Set)
Corresponding
ACPU
D9
Corresponding
CPU