EasyManua.ls Logo

MTD 300 Series - User Manual

MTD 300 Series
44 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
P. O. Box 1386, 97 KENT AVENUE, KITCHENER, ON N2G 4J1
Printed In USA
OPERATOR’S MANUAL
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
769-07158
08.31.11
Two-Stage Snow Thrower — 300 Series

Table of Contents

Other manuals for MTD 300 Series

Preview: Shop Manual
Shop Manual44 pages

Questions and Answers

  • S
    Shawn JoyceAug 16, 2025
    How to troubleshoot starting issues with my MTD Snow Blower?
    • J
      Jenna ClarkAug 16, 2025
      If your MTD Snow Blower engine won't start, there are several potential causes: * The choke might not be in the CHOKE position; move it to the CHOKE position. * The spark plug wire could be disconnected; connect it to the spark plug. * The fuel tank may be empty or contain stale fuel; fill it with clean, fresh gasoline. * The engine might not be primed; prime it as instructed in the Operation Section. * The spark plug could be faulty; clean, adjust the gap, or replace it. * The key is not in the ignition; insert the key fully into the switch.
  • J
    john00Aug 19, 2025
    What to do if my MTD 300 fails to discharge snow?
    • O
      Olivia GonzalezAug 19, 2025
      If your MTD Snow Blower isn't throwing snow, the chute assembly might be clogged. Stop the engine, disconnect the spark plug wire, and then use a clean-out tool or stick to carefully remove any blockage from the chute and inside the auger housing. Also, check the shear pins; if they're broken, replace them. Ensure no foreign objects are lodged in the auger. If there is, stop the engine immediately, disconnect the spark plug wire, and remove the object. Furthermore, the auger control cable might be out of adjustment, so adjust the auger control cable. Finally, the auger belt could be loose or damaged, in which case you should replace it.
  • T
    Teresa LynchAug 22, 2025
    What to do if my MTD 300 won't throw snow?
    • L
      lhullAug 23, 2025
      If your MTD Snow Blower isn't discharging snow, here's what might be happening: * The chute assembly could be clogged. Stop the engine, disconnect the spark plug wire, and clean the chute and inside of the auger housing with a clean-out tool or stick. * Shear pins might be sheared. Replace them. * A foreign object may be lodged in the auger. Immediately stop the engine, disconnect the spark plug wire, and remove the object. * The auger control cable could be out of adjustment. Adjust the auger control cable. * The auger belt might be loose or damaged. Replace the auger belt.
  • A
    Ariel Williamson MDAug 26, 2025
    How to stop the augers from rotating on my MTD 300?
    • S
      Scott OlsonAug 26, 2025
      If the augers on your MTD Snow Blower keep spinning, the cable might need adjustment. Adjust the auger control cable as shown in the 'Adjusting Auger Cable' section.
  • F
    fmooneyAug 28, 2025
    Why won't my MTD 300 Snow Blower move by itself?
    • B
      Brandon BrooksAug 28, 2025
      If your MTD Snow Blower won't move on its own, the drive belt may be loose or damaged; in this case, replace the drive belt. Also, the single speed transmission might be damaged, so see an Authorized Service Dealer.
  • L
    Lee DavenportAug 31, 2025
    Why is my MTD 300 engine running rough?
    • S
      simmonsjoshuaAug 31, 2025
      If your MTD Snow Blower engine is running erratically with inconsistent RPMs, consider these possibilities: * The engine might be running on CHOKE. Move the choke lever to the RUN position. * The fuel could be stale. Fill the tank with clean, fresh gasoline. * There may be water or dirt in the fuel system. Drain the fuel tank and refill with fresh fuel. * The carburetor might be out of adjustment. Contact an authorized Service Center. * The engine may be over-governed. Contact an authorized Service Center.
  • E
    Elizabeth WardSep 3, 2025
    What to do if my MTD Lawn and Garden Equipment unit fails to discharge snow?
    • U
      ustewartSep 3, 2025
      If your MTD Lawn and Garden Equipment unit isn't discharging snow, several factors could be at play. First, the chute assembly might be clogged; in this case, stop the engine, disconnect the spark plug wire, and use a clean-out tool or stick to clear the chute and the inside of the auger housing. Second, check for sheared shear pins and replace them if necessary. A foreign object lodged in the auger could also be the culprit; if so, immediately stop the engine, disconnect the spark plug wire, and remove the object. Additionally, the auger control cable might be out of adjustment, requiring adjustment. Finally, inspect the auger belt for looseness or damage, and replace it if needed.
  • M
    Matthew RileySep 6, 2025
    Why is there excessive vibration in my MTD Lawn and Garden Equipment?
    • B
      Bryan MayerSep 6, 2025
      Excessive vibration in your MTD Lawn and Garden Equipment is likely due to loose parts or a damaged auger. Immediately stop the engine and disconnect the spark plug wire. Inspect the unit for any damage and tighten all bolts and nuts. Repair any damage you find. If the vibration continues after these steps, it is recommended to take your unit to an authorized service dealer.
  • J
    Julie RomeroSep 9, 2025
    What to do if my MTD Lawn and Garden Equipment unit fails to self-propel?
    • O
      Olivia DavenportSep 9, 2025
      If your MTD Lawn and Garden Equipment unit isn't self-propelling, the drive belt is likely loose or damaged. Replace the drive belt to resolve this issue.
  • C
    Carl ScottSep 12, 2025
    How to fix MTD Lawn and Garden Equipment augers that continue to rotate?
    • C
      christina72Sep 12, 2025
      If the augers on your MTD Lawn and Garden Equipment continue to rotate, the cable is likely out of adjustment. You should adjust the auger control cable as shown in 'Adjusting Auger Cable' section.

MTD 300 Series Specifications

General IconGeneral
BrandMTD
Model300 Series
CategorySnow Blower
LanguageEnglish

Related product manuals